Answered: 5/ Determine the smallest value of…

5/ Determine the smallest value of uniform load that will cause a crack for the reinforced concrete beam shown below. Use f= 30 MPa Wer=? 3.6 m- Ø16mm 100 600 100-> 100 200 50

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Related questions

Q: An aluminum bar having a cross-sectional area of 160 mm² carries the axial loads as shown in the…

Q: A cantilever beam with a 'T' shaped cross-section is loaded with a distributed load as shown below.…

A: Width of flange= 80 mm Height of web = 75 mm

Q: CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between…

Q: Q4: A rectangular beam has the dimensions shown in figure below. Tensile strength in bending…

A: Given: Modulus of rupture, fcr = 3.5 MPa M = 63 kNm fc = 25 MPa fy = 414 MPa Es = 200000 MPa Ec =…

Q: A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z…

Q: Compute the bending stress of the beam shown. Assume that the concrete has cracked and use the…

A: Answer We know that Bending stress of the beam can be computed using the following equation Bending…

Q: The given figure shows an l-section of the beam. The shear stress at a point B is 12 MPa. The stress…

A: Given- I section beam- Shear stress at B=12 MPa,

Q: : Calculate the bending stresses in concrete and steel if f, =345 MPa and the concrete strength fe =…

Q: Calculate the tensile steel strain of 5-16-mm-dia rebars in a concrete beam 200 mm by 440 mm at…

Question

5/Determine the smallest value of uniform load that will cause a crack for the reinforced
concrete beam shown below. Use f= 30 MPa
Wer=?
3.6 m-
Ø16mm
100
600
100->
100
200
50

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN. 0.8m 0.4m B 5KN 0.6m Al 20KN Q2 5) What is the deformation 8, in mm? A=800 mm? A=1,200 mm?
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
Prove each of the following equations separately 30 0x - 270 ([1-sin() sin(³9)] y Exy| Oxx 30 cos 1+ sin sin 270 30 K cos() sin() cos(32) K₁ x 2.70 Stresses near the tip of a crack in an elastic material. Crack FIGURE COS
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
q7 A steel bar 2 m long, 20 mm wide and 15 mm thick is subjected to a tensile load of 30 kN. If Poisson's ratio is 0.25 and Young's modulus is 200 GPa, an increase in volume will be (b) 150 mm3 (d) 130 mm3 (a) 160 mm3 (c) 140 mm3
What is the cracking moment of the beam having a cross section shown in Figure 1if f ‘c = 28 MPa?.
2. Shown below are pieces of unsaid material. They are combined and locked in each other and a force P is pulling each side. Assuming that the Shear stress for the material is 38 MPa, Determine the force P needed to fracture the materials in shear. 30 mm 30 mm 80 mm Section A-A
E 0.4m D 10KN 0.8m 0.4m В 5KN 0.6m Al 20KN A=800 mm? A=1,200 mm?
A test conducted on a steel bar whose cross section is 0.5 in. by 4 in. is performed. Anaxial load of P = 30,500 lb. produced a deformation of 0.00103 in. over a gauge lengthof 2 in. and a decrease of 0.000078 in. in the 0.5-in. thickness of the bar. Determinea. Poisson’s ratio,b. the elastic modulusc. the decrease in the 4-in. cross-sectional dimension.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m 5KN 0.6m A 20KN 3) What is the deformation &cn in mm? A=800 mm? A=1,200 mm²
Please see the image attached. Thank you