b) A bored pile was installed in dense sand with the following data:Diameter of pile 600 mm, length of pile= 20 m of internal friction () = 30°, 1=20kN/mThe ground water table was at a depth of 6 m. below the ground surface. Assuming factor ofsafety of 3 calculate the estimated safe load capacity of a single pile.%3D

Diameter of pile (d) = 0.6 mLength of pile( L) = 20 mAngle of internal friction(ϕ) = 30°γ = 20…

b) A bored pile was installed in dense sand with the following data- kN/m The ground water table was at a depth of 6 m. below the ground surface. Assuming factor of safety of 3 calculate the estimated safe load capacity of a single pile.

b) A bored pile was installed in dense sand with the following data- kN/m The ground water table was at a depth of 6 m. below the ground surface. Assuming factor of safety of 3 calculate the estimated safe load capacity of a single pile.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A rectangular pile (0.5 x 0.5 m.) is driven in a clayey soil arrangement composed of two different…

A: Please refer the attached image for complete solution. THANK YOU.

Q: slipping when it makes an angle of 60 degree from the horizontal, determine the tension of the cord…

Q: A wooden pile is driven with a drop hammer weighing 20 kN and in the second trial it was driven with…

A: Gjj

Q: For the figure shown if the pile length is 15 m Find the factor of safety (Fs), if the allowable…

Q: Calculate the pile point bearing capacity using Meyerhof's Method, where a Concrete pile of diameter…

A: The given data is: Diameter of concrete pile=12 in Length of pile=25 ft Unit weight of sand, γ=128…

Q: Consider a precast concrete pile that is 0.505 m X 0.505 m in cross section driven in a homogeneous…

A: The following are the given information, Pile Cross section = 0.505 m x 0.505 m Homogeneous sand…

Q: Determine ultimate carrying capacity of pile of diameter 0.3m and length 10m driven into sandy soil…

A: Diameter of the pile = D = .3mLength of the pile = L = 10mUnit weight of soil = γ = 17KNm2ϕ = 30°

Q: A pre-cast wooden pile is being driven with 50 kN drop hammer having a free fall of 100 cm.…

A: Drop hammer weight W=50 kN, Free fall H=100 cm, Penetration S=0.45 cm,

Q: 3- The pile is classified as Micro (Mini) pile when its diameter is: *less than 0.2m less than 0.3m…

Q: A 14-in.-diameter steel pipe pile is driven 50 ft into overconsolidated clays having the following…

A: The ultimate bearing capacity of the pile is given by,

Q: A concrete pile is 15 m long and has 406 mm diameter circular cross section. The pile is fully…

Q: A 16 in diameter, 55 ft long drilled displacement pile is to be constructed in the following soil…

A: Calculate the Toe Bearing capacity: The construction method for DD piles does not provide any…

Q: An 18-in.-diameter, closed-ended steel pipe pile is driven 45 ft through soft sandy silt to bear on…

A: The tip resistance is generally obtained by the force required to push the tip of the cone…

Q: For a load of 1200 kN and assuming an overall factor of safety of 2.5, determine the required length…

A: the problem involves determining the required length of a pile for a given load and safety factor.…

Q: A singly under-reamed, 8-m long, RCC pile (shown in the adjoining figure) weighing 20 kN with 350 mm…

A: Given- Weight of the pile Ps=20 kN, Diameter of the shaft Do=350 mm, Under ream dia Du=750 mm,…

Q: rectangular pile (0.54 x 0.63) is driven in clayey soil arrangement composed of two different…

Q: 3. As shown in the diagram, the RC solid precast square pile will be lifted up by two points, the…

Q: and thereafter, Cu 132, 32, where z is the depth Z IS each strata. Determine the ultimate capacity…

Q: Consider a continuous flight auger pile in a sandy soil de- posit 10 m long with a diameter of 0.45…

A: Given:

Q: A wooden pile is driven with a drop hammer weighing 20 kN and in the second trial it was driven with…

Q: A closed end precast concrete pile with a diameter (Dp) of 0.5 m is driven into a uniform sand…

A: L1=4To determine the ultimate load-carrying capacity (Qₚ) for a closed-end precast concrete pile…

Q: Explanation of nouns: 1. Static pressure pile 2. Soil penetration 3. Mechanical connection of steel…

A: 1. Static pressure pile: The static pressure pile process of construction of existing building…

Q: Determine the breaking wave load on a 1 ft diàmeter pile in a design water depth of 5 ft.

A: We assume breaking load on pile acts at silt water level .. Given Dia of pile = 1 ft.(round pile)…

Q: determine: Pile Load Test -- You are to use the results of a pile load test given below to A. The…

A: The question might be related to calculating the equivalent resistance (Req) of the parallel…

Q: Calculate the minimum and maximum axial compressive capacity of a 1.2 m diameter closed- ended steel…

A: D(diameter of pile) = 1.2m The top layer of sand and second layer of clay will only provide skin…

Q: What would be the estimated ultimate tensile capacity of the pile?

Q: A 50 cm square prestressed concrete pile will be driven 20 m into the soil profile below. (water…

A: Given: A_b = (50 cm)2 / (100 cm/m)2 * pi / 4 = 0.196 m2 c' = 4 kPa (using ϕ= 28 deg) N_c = 14.7 N_q…

Q: Describe the following briefly: (a) Negative Skin friction and its estimation. (b) Dynamic…

A: Negative skin friction or 'down drag' is a phenomenon, in which portion of a soil layer surrounding…

Q: on a site nderlain by expansive Deen recommended. The

Q: Q3 The system shown in figure find the following: a-flow rate per meter length of sheet pile ,if k=…

A: K=1x10-4 m/sec, L=1.5 m, Void ratio(e)=0.57, Specific gravity(G)=2.68.

Q: ΤΑ 9 kips/ft 10'- B 20 kips 6'- 6². 9 kips/ft C 10- D

A: To draw BMD and SFD using the Moment Distribution Method

Q: A- The load (Q=900 ton) locate at x, determine the max. & min. pile reaction for the given condition…

A: The pile is the supporting or substructure for the bridge or building when loading is acting due to…

Q: own in figure below. Use a FS = 3 if necessary. Assuming that pile setties se shear strength of the…

Q: Discuss the method of obtaining ultimate load and also allowableload on a single pile from pile load…

A: Pile load test is the in situ method of the calculation of the load and settlement. This method is…

Q: 525 kN Medium clay 5 m Cu = 60 kPa Stiff clay Cu = 100 kPa

Q: Please solve under Geotechnical Engineering II.

A: To determine the required length of the pile, we'll use the ultimate bearing capacity formula for…

Q: The horizontal floor with a length of 15 m, has one downstream sheet pile with a depth is 12 m, an…

A: H=3 m Take ρ of concrete=2.45α=bd=1512=1.25λ=1+1+α22=1+1+1.2522=1.3 Required: To calculate floor…

Q: A rectangular pile (0.88 x 0.68 m.) is driven in a clayey soil arrangement composed of two different…

Q: A pile is driven into the ground with a drop hammer weighing 1200 kg and having a free fall of 2.0…

A: Given data- Weight of drop hammer W=1200 kg, Free fall H=2 m=200 cm, Penetration S=1 cm, To Find-…

Q: please answer fast.

A: Step 1:Step 2: Step 3: Step 4:

Q: SITUATION 1: A pre-stressed concrete pile of length L is to be picked up by crane at two points,…

A: Due to the loading in the pile no cracking will be form hence the positive bending moment at mid of…

Q: RL=105m V (U/s water level) RL=100m (D/s water level) 3m 6m Pile Pile 15m 10m 2m 8m For the above…

Concept explainers

Pricing Excavation and Backfill

Backfill, in construction, is the activity of returning the soil and gravel that are removed during building construction or using them again to toughen and support the foundation of the building or any other structural component.

Question

100%

b) A bored pile was installed in dense sand with the following data:
Diameter of pile 600 mm, length of pile= 20 m of internal friction () = 30°, 1=20
kN/m
The ground water table was at a depth of 6 m. below the ground surface. Assuming factor of
safety of 3 calculate the estimated safe load capacity of a single pile.
%3D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Data

VIEW

Step 2: Critical depth

Step 3: Graph

Step 4: Safe load

Step 5:ANSWER

Step by step

Solved in 5 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The Young’s modulus of the concrete of the piles is 75.8 GPa and the concrete unit weight is 25 kN/m3. If the hammer strikes the pile at 3 m/s, and the pile cushion has the same cross-sectional area of the pile with a modulus of 2×105 kPa and a unit weight of 7 kN/m3, complete the wave equation analysis of the pile after one impact. Set the problem up in an Excel spreadsheet to carry the calculations until the movement of the pile stabilizes. Plot the displacement of the pile versus time. Note, when calculating the pile spring only, assume an element length of 4 m. This is still long but using the actual element length will make your constant too small, impacting the damping. Note that if using software elements would be less than 1 m.
7) A sheet pile is installed in a soil with coefficient of permeability equal to 10-6 m/s. The flow net formed around the pile has 6 flow lines and 14 equipotential lines and the difference in height of water at each side of the pile is 3 m. Calculate the rate of seepage per unit width of pile.
A concrete pile 0.133ft by 0.133ft in cross section is shown below. Pile length 10 m . Answer a) ii, iii, iv
Determine load carrying capacity of pile without considering critical depth concept. Diameter of pile 0.4 m.Ng =132 for o = 40° to m y 4.b Cot-opf "loose Sand K=1 = 21-15 From. 8a 19 Cu 20k Demse Sund 2 20 $=40° K=2 -I 30°
Q3- regarding the group pile shown in figure Q3, the piles having a diameter of 457 mm, located at (4) m center to center and embedded to depth of 16 m in sandy soil. Determine the group pile efficiency if the soil unit weight is 17.9 kN/m3 and angle of internal friction is 32o.
Q3- regarding the group pile shown in figure Q3, the piles having a diameter of 457 mm, located at (4) m center to center and embedded to depth of 16 m in sandy soil. Determine the group pile efficiency if the soil unit weight is 17.9 kN/m3 and angle of internal friction is 32.
What is the significant role of setup and relaxation on driven pile capacity?
Calculate the side resistance in pounds for a 20 ft long open ended 27 inch diameter smooth steel pipe pile driven in sand with a friction angle of 35 degrees using the beta method. Assume the water table is at the ground surface. The unit weight of the soil is 126 pcf. The overconsolidation ratio is one.
A 16 in diameter, 75 ft long drilled displacement pile is made of grout with f'c = 5,000 lb/in2. A steel ratio of 0.04 is to be used in the upper 30 ft, and a steel ratio of 0.001 for the remainder of the pile. Compute the modulus of elasticity for the upper and lower portions of this pile.
A HP 13x100 steel pile of length 40 feet is driven with a hammer of rated energy 30 kip-ft, weight 12 kips. A. Use the Gates method to determine refusal criterion if the ultimate pile capacity is to be 600 kips. B. Will the pile survive during installation?
A concrete pile is 15 m long and has 406 mm diameter circular cross section. The pile is fully embedded in sand, for which the unit weight '( = 18 kN/m3 and the frictional angle 8 = 30°. i) Calculate the ultimate point load Qp ii) Determine the total frictional resistance Qs iii) Determine the total ultimate load ofthe pile.
A square prestressed concrete pile with a 14 inch side is to be driven to the necessary depth. It needs to be able to support 105 kips. It has been determined that the point resistance qp is 120 ksf and the side friction fs is 450 psf. Use formula 12.2 (see attached image) to estimate how long the pile needs to be with a factor of safety of at least 2.5. Round your answer to a multiple of 5 feet. Use L as a variable to calculate the load in formula 12.2. L can be obtained from this equation.