4. The figure shows the cross section of a simply supported beam that carries a uniformly distributed loading of intensity 180 Ib/ft over its entire length L. If the working shear stress is 120 psi, determine the largest allowable value of L. 6 in. 8 in. 10 in. 8 in.

4. The figure shows the cross section of a simply supported beam that carries a uniformly distributed loading of intensity 180 Ib/ft over its entire length L. If the working shear stress is 120 psi, determine the largest allowable value of L. 6 in. 8 in. 10 in. 8 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q3/ A steel rod which length is (91.44cm) and the diameter (1 inch), after it pulled by a (100N) force the magnitude of elongation strain was (1.6cm). Find the Yong modulus of the steel rod.
If the maximum shear stress acting on rectangular beam is 50 N/mm², determine the average shear stress? Select one: Ⓒa. 31.5 N/mm² Ob. 33.33 N/mm² O c. 37.5 N/mm² Od. 42.5 N/mm²
A beam with varying load is shown at the figure below. If the beam properties are given, what is the final stress at bottom of the beam at midspan where total losses of the prestressing force is 27% (MPa) Properties: Beam width = 290 mm Beam height = 463 mm Varying load = 19.6 kN/m Span of the beam 10 m Prestressing force = 481 kN %3D eccentricity = 126 mm Wo (kN/m)
A simply supported wood beam is reinforced with a steel plate of width b as shown in the figure. The beam carries a uniformly distributed load including the weight of the beam) of intensity 285 lb/ft over its 19.1-ft span. Using b = 4 in. and Est/Ewd = 20, determine the maximum bending stress (in psi) in the steel.
A steel beam, of lengths a = 6 m and b = 3 m and a hollow box cross section, is supported by a hinge support A and roller support B, see Figure Q.1. The width and height of the cross section are 200 mm and 300 mm, respectively, and the wall thickness of the cross section is 5 mm. The beam is under a distributed load of the intensity that linearly varies from q=0 kN/m to q = 3.1 kN/m for AB span; and is constant with q = 3.1 kN/m for BC span. The Young's modulus of steel is 200 GPa. A y, v a 5 mm 200 mm Figure Q.1 9 A B 300 mm b C X
A large uniform plate containing a rivet hole is subjected to uniform uniaxial tension of 50MPa. Where its diameter is 2 cm and width 5cm. Find maximum stress in the plate.
Determine the flexural stress and shear stress of the beam loaded as shown in the figure with shear diagram and moment diagram
A steel beam, of lengths a= 6 m and b= 3 m and a hollow box cross section, is supported by a hinge support A and roller support B, see Figure Q.1. The width and height of the cross section are 200 mm and 300 mm, respectively, and the wall thickness of the cross section is 5 mm. The beam is under a distributed load of the intensity that linearly varies from q = 0 kN/m to q = 3.1 kN/m for AB span; and is constant with q= 3.1 kN/m for BC span. The Young's modulus of steel is 200 GPa. Part A Calculate: A y, v a 5 mm 200 mm Figure Q.1 9 S B 300 mm b с X
Determine the flexural stress and shear stress of a rectangular beam loaded as shown in the figure below.