Answered: For the beam shown in Figure (2), given…

For the beam shown in Figure (2), given INA = 1.25 106mm, calculate the following: 1) Flexural stress at point A on the section at the mid-span of the beam. 2) Maximum absolute flexural stress.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 με is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P?
3. An A36 Steel Cantilever Beam is shown below, also showing its cross section. Determine the following: Given the formula of the Maximum allowable bending stress of steel, fb = 0.66Fy. Where Fy is the Yield Stress of Steel. Where the bending stress for a beam is (fb) = Mc/I, where c is the distance of the centroid to the extreme most fiber of the beam (either top-most or bottom-most distance). Does the Steel fail under the loading given? Use Fy = 450 Mpa. Use the Moment in (a) and the moment of inertia in (c).
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
Maximum allowable (safe) bending stress for a beam AB under a constant distributed load as shown in the figure.It is 40 MPa.a) What is the maximum value of the length (L) of the beam in this case?b) Draw the shear stress (τ) profile where the V (shear in section) force is greatest.Hint: You can specify several points in the section and calculate the shear stress for those points.
Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal pressure, and a torque. In points A and B, the following stresses occur due to the loading: o 63.5 MPa, B=127 MPa, = 127 MPa A.B A.B a. Determine Gmin, omax, and its direction (in degrees) from x-axis at point A. b. Determine omin, omax, and its direction (in degrees) from x-axis at point B. 1 B d O A x
6.59 A square section as shown in the figure below is subjected to bending moment M. (c) Obc = Obl y || h y H What is the maximum bending stress? (a) Obc = obt 12M h³ 9M 2h³ JXC h (b) bc = Obt = (d) %bc =%bt = 6M 4³ 9M h³
A steel cantilever beam 6 m in length is subjected to a concentrated load of 120 N acting at the free end of the bar. The cross section of the beam is shown below. deep. Determine the magnitude and location of the maximum tensile and compressive bending stresses in the beam. As usual, neglect the weight of the beam. 4mm 120 N 1mm 1mm 6mm 6m 1mm 4mm
A square beam (w=0.03 m) is loaded with a point load of 1000 N and a moment load of 1000 Nm, as shown. i. Determine maximum deflection of the beam using step by step analytical equations. ii. Determine the Maximum stress in the beam using step by step analytical equations iii. For both top fibers and bottom fibers of the square beam, specify the type of the stresses.
Q1: The beam shown in Figure 1 is subjected to a vertical force Pv and a horizontal force Ph. The data for Pv, Ph, a,L,and e are shown in Table 1. Determine the maximum compressive and tensile stresses under the vertical force (at a distance a from the left support.) Pv = 80k N a = G0o 6 omm e %3D 26 K N 120 mm L =3600 mm Figure 1 250 mm
Question 5 A steel column with a rectangular hollow section is subject to a vertical downward load P1 and a horizontal load P2, as shown in Figure 5 below. If the width of the hollow section is 70mm and the thickness is 5mm, determine the maximum compressive stress at the base of the column. P1=500KN, P2=100kN. P1 - P2 e =110mm Top plate- P2 P1 1m L120mm 120mm (b) Top view showing location of loads (a) Column elevation Figure 5: The cantilever column is fixed at the base.
Question 2) Find the shear center of the section below and calculate the maximum shear stress that occurs in the section as a result of the loading shown in the figure. The section thickness is uniform everywhere and is 10 mm. Note: G.M is the geometry center of the section, the shear force of 40 kN acts from the geometry center of the section. You can look at your lecture notes for the coefficients you will need. 160 mm V-40 kN t LG.M 100 mm
A cantilever beam of length 6 m has an additional support at a distance of 2 m from its free end as shown in Figure 4. It has the cross-sectional dimensions with height h=300 mm, inside height h₁ =250 mm, width b= 150 mm, and inside width b₁=100 mm. It is made of an elastic perfectly plastic material having tensile and compressive yield stress of oy = 250 MPa. Determine the yield moment My of the beam Determine the plastic moment Mp of the beam ✓ By using force method and selecting the vertical reaction at C to be redundant, draw shear and bending diagrams using the graphical method. -Determine the minimum value of W at which collapse occurs B/2W C 77 2m 2m 2m C b₁