L For the beam shown above with length L= 7 m with the applied uniformly distributed load of w = 17 kN/m, what is the maximum bending stress if the beam has a cross section with the following dimensions: b = 100 mm d = 250 mm tf = 20 mm tw = 15 mm b tw

L For the beam shown above with length L= 7 m with the applied uniformly distributed load of w = 17 kN/m, what is the maximum bending stress if the beam has a cross section with the following dimensions: b = 100 mm d = 250 mm tf = 20 mm tw = 15 mm b tw

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Figure 1 below shows a cantilever beam subjected to an axial compressive load of 450 kN acting at…

A: Given:- Width B=150 mmDepth D=300 mm1.1 Direct compressive stress=PA=450×103300×150=10…

Q: A beam has a concentrated load (Pu) at midspan and has a fixed support at both ends. If the beam…

A: Given: The width of the beam is 271 mm. The height of the beam is 462 mm. The load Pu is 58.15 kN.…

Q: Determine the maximum bending stress (in MPa, numerical value only) of the beam shown below with the…

Q: AW310 x 38.7 standard steel shape is used to support the loads shown on the beam in the figure.…

Q: Take XX=200 KN

A: Given data : Compressive load (P)=200 KNCross sectional area (A)=100×100 mInitial length (L)=1.70…

Q: mm rectangles arranged as shown. A. Determine the maximum value of w without exceeding the…

A: solution of above problem is below:

Q: operties: eam width = 229 mm %3D eam height = 437 mm %3D arying load 9.46 kN/m niform load = 4.81…

A: Moment at 2.84m from Right Support = 35.85Kn-m Moment of Inertia = Bd3/12 = 1.59 x 109 Stress at top…

Q: 2. For the beam shown, determine the following: a. Maximum tensile stress in the beam. b. Maximum…

Q: A beam with varying load is shown at the figure below. If the beam properties are given, what is the…

A: Given data: Beam width = 276mm Beam depth = 411mm Span length = 9m Varying load = 18.45 Kn/m Pre…

Q: For the given figure below and its properties, calculate the stress at the bottom where at the fixed…

A: We will calculate moment at fixed end and use bending equation.

Q: A beam with varying load is shown at the figure below. If the beam properties are given, what is the…

A: Beam : A beam is a horizontal element that spans an opening and supports a weight, which could be a…

Q: A beam with varying load is shown at the figure below. If the beam properties are given, what is the…

A: Introduction: Prestressing process involves application of an initial compressive pre-stress on a…

Q: A bar of length 1.70m has a square cross section of side 100 mm (as show. in the figure). The bar is…

Q: Figure Q2 shows a simply supported beam carrying two point loads. The beam has the cross-section…

A: Figure is as shown

Q: A cantilever beam made or square tuce (as shown below) has a length L = 1 m. The bar is required to…

Q: A beam has a bending moment of 4 kN-m applied to a section with a hollow circular cross-section of…

A: Given bending moment M =4 KN-mdia of hollow section Do=3.3 cm=33mmand inner dia Din=2.3 cm=23…

Q: A simply supported beam is carrying a varying load and a uniform load as shown in the figure. If the…

A: Find reaction forces Since the distance from which final stress needs to be found out is 2.76 m…

Q: +2m R₁ Wo 3m R₂ T 25 mm k 200 mm 25 mm 250 mm 25 mm

Q: A wood beam carries the loading shown in the figure. Determine the smallest allowable width b of the…

Q: Upvote will be given. Please write the solutions legibly. Solve in 2 decimal place 15 KN 20 KN/m 4m…

Q: A beam with varying load is shown at the figure below. If the beam properties are given, what is the…

Q: A simply supported beam of span 4 m carries a concentrated load Pin kN acting downward at distance…

Q: A simply supported beam is carrying a uniform load. If the beam properties are given below, what is…

Q: simply supported beam is carrying a uniform load.

A: Given: Beam width, b = 285 mm Height, d =475 mm Uniform load = 9.1 kN/m Span, L = 13 m Prestressing…

Q: Determine the maximum tensile and compressive bending stress developed in the beam.

A: ##Calculation Maximum Tensile and Compressive Bending stress ####

Q: A beam has a bending moment of 3.5 kN-m applied to a section with a hollow circular cross-section of…

A: Note:- Hi, thank you for the question. As per our Honor code, we are allowed to attempt the first…

Q: A wooden beam whose length is 1 m is 100 mm wide and 200 mm high. It carries a load of 100 kN as…

A: Given data :- A wooden beam length = l = 1m width = b = 100 mm = 0.1 m height = h = 200 mm = 0.2 m…

Q: Figure 3a shows the loading, shear force diagram and bending moment diagram of a simply-supported…

Q: W

A: Bending stress is give an idea about the moment carrying capacity of the section Different section…

Q: For each of the loadings shown below, write the load using singularity functions and give the…

Concept explainers

Members with compression and bending

Compression members are structural elements that carry compressive axial force. They are the vertical members of a building that support beams and their design, which is governed by buckling and strength. Columns are known as struct or compression members, which are subjected to compressive forces. These members provide stiffness to the building and avoid any imperfection regarding the transfer of axial load. For instance, webs in a truss, braces in a framed structure, tiers, and so on.

Question

L
For the beam shown above with length L = 7 m with the applied uniformly distributed load of w = 17
kN/m, what is the maximum bending stress if the beam has a cross section with the following
dimensions:
b = 100 mm
d = 250 mm
tf = 20 mm
tw = 15 mm
%3D
b
tw
O bending
MPa Round to one decimal place

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

a simply supported beam is carrying a varying load and a uniform load as shown in the figure. If the beam properties are given below, what is the final stress at bottom of beam section at a distance 2.47m from the right support where the totall losses of the prestressing force is 24% mpa beam wid=217mm height= 480mm varying load= 9.67kn/m uniform load = 4.27 kn/m x = 3.32 y = 5.95 Prestressing force = 429kn eccentricity = 95mm
A beam has a concentrated load (Pu) at midspan and has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at 3.19 from the support. (MPa) Properties: Beam width = 211 mm Beam height 389 mm 27 Pu 63.66 kN Span of the beam 8 m Prestressing force 326 kN eccentricity = 95 mm
The steel beam has the cross section shown. The beam length is L = 6.4 m, and the cross-sectional dimensions are d = 345 mm, by = 205 mm, t = 16 mm, and tw = 7 mm. Calculate the largest intensity of distributed load wo that can be supported by this beam if the allowable bending stress is 215 MPa. Answer: Wo Wo kN/m T₁₂ y
A beam with varying load is shown at the figure below. If the beam properties are given, what is the final stress at bottom of the beam at midspan where total losses of the prestressing force is 27% (MPa) Properties: Beam width = 290 mm Beam height = 463 mm Varying load = 19.6 kN/m Span of the beam 10 m Prestressing force = 481 kN %3D eccentricity = 126 mm Wo (kN/m)
Q.3.L
A beam has a concentrated load (Pu) at midspan and has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at 3.4 from the support. (MPa) Properties: Beam width - 211 mm Beam height = 414 mm Pu 73.09 kN Span of the beam = 10 m Prestressing force = 509 kN eccentricity = 130 mm
L For the beam shown above with length L = 7 m with the applied uniformly distributed load of w = 14 KN/m, what is the maximum bending stress if the beam has a cross section with the following dimensions: b = 100 mm d = 250 mm t = 20 mm tw = 15 mm tw
A simply supported beam is carrying a uniform load. If the beam properties are given below, what is the final stress at top of the beam section at midspan where the total losses of the prestressing force is 21% (MPa) Properties: Beam width = 263 mm Beam height = 455 mm Uniform load = 6.9 kN/m Span of the beam = 12 m Prestressing force = 359 kN eccentricity = 115 mm
please step by step solution