The following figure shows a simply supported beam carrying a uniformly distributed load (udl) of 10 kN/m. Assuming the beam to have a rectangular cross-section of 240 mm (b) × 400 mm (h), draw the state of stress at infinitesimal elements A, B, C and D as shown. udl = 10 kN/m NA C +-1000 1000 2000mm

The following figure shows a simply supported beam carrying a uniformly distributed load (udl) of 10 kN/m. Assuming the beam to have a rectangular cross-section of 240 mm (b) × 400 mm (h), draw the state of stress at infinitesimal elements A, B, C and D as shown. udl = 10 kN/m NA C +-1000 1000 2000mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. Determine the maximum compressive and tensile stress in beam AB as shown in the figure and draw the stress distribution over the cross section at this location. 25 kN/m 5m 50 KN 5m 4 m 50 KN 150 500 450 150
i need the answer quickly
Tb = 80.51
A beam with varying load is shown at the figure below. If the beam properties are given, what is the final stress at bottom of the beam at midspan where total losses of the prestressing force is 27% (MPa) Properties: Beam width = 290 mm Beam height = 463 mm Varying load = 19.6 kN/m Span of the beam 10 m Prestressing force = 481 kN %3D eccentricity = 126 mm Wo (kN/m)
For the stress state listed below: Ox = 85 MPa Oy = -62 MPa Txy = -28 MPa 1. Use software of your choice (Excel, Matlab, etc.) and plot Mohr's circle. 2. Using a protractor, or graphically using computer code, measure the rotations necessary for the principal stress plane and the plane of maximum shear.
240 mm 120 mm 240 mm 240 mm 120 mm 240 mm Determine the magnitude of the maximum shear stress at the cross section if V=120 kN. Express your answer in MPa and use three significant figures.
In the Figure 5, the normal stress on the cross- sectional area is (in Mpa): Figure 5: у P = 400 KN X 30 mm 1000 mm 30° Area 20 mm الاختيارات 577 O 597 587 O 567
The two sub questions and question g as well :
A simply supported wood beam is reinforced with a steel plate of width b as shown in the figure. The beam carries a uniformly distributed load including the weight of the beam) of intensity 285 lb/ft over its 19.1-ft span. Using b = 4 in. and Est/Ewd = 20, determine the maximum bending stress (in psi) in the steel.
The bending moment Mx affects the cross section of the beam given in the figure. Calculate the normal stress values that will occur at points 1,2,3 of the beam section and plot the normal stress distribution.
1. For the beam showing in the figure, consider section n-n and determine; (a) The largest shearing stress in that section (b) The shearing stress at point a. 0.3 m 40 nim 10 KN 12 imm 150 mm 12 mm 200 mm 15 in
A simply supported beam is carrying a varying load and a uniform load as shown in the figure. If the beam properties are given below, what is the final stress at top of the beam section at a distance 2.57m from the right support where the total losses of the prestressing force is 21% (MPa) Properties: Beam width = 293 mm Beam height = 382 mm %3D Varying load = 8.98 kN/m Uniform load = 5.11 kN/m x 3.35 mm y = 7.05 mm Prestressing force = 438 kN eccentricity = 134 mm VL (kN/m) UL (kN/m)