4) A large moveable plate is located between two large plate as shown in the figure. Determine the magnitude and direction of the shearing stresses that act on the fixed walls when the moving plate has a velocity of 4 m/s. Assume that the velocity distribution between the plates is linear Fixed plate 6 mm A. 0.02 N s/m 4 m/s 3 mm H=0.01 N. s/m Fixed plate

4) A large moveable plate is located between two large plate as shown in the figure. Determine the magnitude and direction of the shearing stresses that act on the fixed walls when the moving plate has a velocity of 4 m/s. Assume that the velocity distribution between the plates is linear Fixed plate 6 mm A. 0.02 N s/m 4 m/s 3 mm H=0.01 N. s/m Fixed plate

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The following figure shows a simply supported beam carrying a uniformly distributed load (udl) of 10…

Q: If the beam is subjected to shear force of V = 12.5 kN as in the figure below, calculate the value…

Q: The stresses shown in the figure act at a point in a stressed body. If σ = 5.8 ksi in the direction…

Q: For a thin plate subjected to the surface traction shown in Figure 6-16, determine the nodal…

A: T = 1000×A = 1000×1×10=10 kips A = 1×10 = 10 in2 E = 30×106 psi = 30×103 ksi AEL…

Q: A sign for an automobile service station is supported by two aluminum poles of hollow circular cross…

Q: A stepped shaft ABC consisting of two solid circular segments is subjected to torques T1 and T2…

Q: 100 mm 100 mm 300 mm If calculating the maximum shear stress, what is the value of Q?

A: It is required to find the value of Q in calculating the maximum shear stress.

Q: QUESTION 1. Longitudinal and cross-sectional views of a beam are given in the figure below. (a) Draw…

Q: c) the value of the maximum bending moment in the beam. Enter your answer in KNM to three decimal…

Concept explainers

Design of structures using FEA

An arrangement, in which various members are interconnected with their constrained relative motion, the whole arrangement is then known as a structure. The degree of freedom of such a structure is zero. In such a structure, the load can act throughout the length of the structure or at the joints.

Question

4) A large moveable plate is located between
two large plate as shown in the figure.
Determine the magnitude and direction of the
shearing stresses that act on the fixed walls
when the moving plate has a velocity of 4
m/s. Assume that the velocity distribution
between the plates is linear
Fixed plate
6 mm
H- 0.02 N. sim
4 m/s
3 mm
A = 0.01 N• sim
Fixed plate

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Answer

VIEW

Step 2:

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

In the built-up box beam shown below, if a vertical shear force is applied, what value of Q, the first moment of area, should be used in determining the shear stress and/or shear flow at point A? Give your answer in m3m3.
1. A hollow steel box beam has the rectangular cross section shown in the figure. Determine the maximum allowable shear force V that may act on the beam if the allowable shear stress is 40 MPa. 10 mm 20 mm 20 Imm 200 mm 450 10 mm mm
please confirm the answer for this.
The stresses shown in the figures act at a point in a stressed body. Determine the normal and shear stresses at this point on the inclined plane using (i) the stress transformation equations. Compare the solution from both the methods.
Same as Example 2.1, except that only the left loaded area exists and the Poisson ratio is 0.3, as shown in Figure 2.8. Determine the stresses, strains, and deflection at point A. E = 10,000 psi v = 0.3 10 in. 50 psi all o, e, w = ? 10 in. FIGURE 2.8 Example 2.2 (1 in. -25.4 mm, 1 psi = 6.9 kPa).
1. Determine the maximum compressive and tensile stress in beam AB as shown in the figure and draw the stress distribution over the cross section at this location. 25 kN/m 5m 50 KN 5m 4 m 50 KN 150 500 450 150
Problem (4.8): A 90-N.m torque is applied to a hollow shaft having the cross section shown in Figure (4.29). Neglecting the effect of stress concentrations, determine the shearing stress at points a and b. 2 mm 4 mm b 40 mm 55 mm 4 mm 55 mm- Figure (4.29)
Please write direct equations and draw graphs if any.
A stepped shaft ABC consisting of two solid circular segments is subjected to torques T1 and T2 acting in opposite directions, as shown in the figure. The larger segment of the shaft has diameter d1 = 2.25 in. and length L1 = 30 in.; the smaller segment has diameter d2 = 1.75 in. and length L2 = 20 in. The material is steel with shear modulus G = 11 x 10^6 psi, and the torques are T1 = 19 kip-in. and T2 11 kip-in. Calculate the shear stress at segment AB in ksi. Note Round up final answer to whole number T2 Įd2 В LI L2
A railroad tie (or sleeper) is subjected to two rail loads, each of magnitude P = 175 kN, acting as shown in the figure. The reaction q of the ballast is assumed to be uniformly distributed over the length of the tie, which has cross-sectional dimensions b = 300 mm and h = 250 mm. %3D Calculate the maximum bending stress omax in the tie due to the loads P, assuming the distance L = 1500 mm and the overhang length a = 500 mm. L h
A beam has a cross-section as shown in Figure Q5. The beam is subjected to a vertical shearing force of 100KN through the shear centre. For the system: a) determine the second moment of area about the x - x plane and b) determine the shear stress distribution along the y – y plane, c) plot the shear stress distribution on a suitable graph, labelling the principal values. y! Centre of Gravity. y' 30 тm 60 тm шш 09 120 тт
Two identical loads distributed over circular areas are applied on an elastic two-layer system, as shown in the figure below. D E = 150,000 psi v = 0.5 h E = 30,000 psi v = 0.5 D/2 the dimensions and the magnitude of the surface stresses are: r= 6.5 in D= 16.25 in g = 75 psi h = 6.5 in Determine: 1. The total vertical deflection at point A 2. The total vertical deflection at point B 3. The total vertical deflection at point C