A stepped shaft ABC consisting of two solid circular segments is subjected to torques T1 and T2 acting in opposite directions, as shown in the figure. The larger segment of the shaft has diameter d1 = 2.25 in. and length L1 = 30 in.; the smaller segment has diameter d2 = 1.75 in. and length L2 = 20 in. The material is steel with shear modulus G = 11 x 10^6 psi, and %3D the torques are T1 = 19 kip-in. and T2 = 11 kip-in. Calculate the shear stress at segment %3D %3D AB in ksi. Note Round up final answer to whole number T2 d2 B |C L - -L2-

A stepped shaft ABC consisting of two solid circular segments is subjected to torques T1 and T2 acting in opposite directions, as shown in the figure. The larger segment of the shaft has diameter d1 = 2.25 in. and length L1 = 30 in.; the smaller segment has diameter d2 = 1.75 in. and length L2 = 20 in. The material is steel with shear modulus G = 11 x 10^6 psi, and %3D the torques are T1 = 19 kip-in. and T2 = 11 kip-in. Calculate the shear stress at segment %3D %3D AB in ksi. Note Round up final answer to whole number T2 d2 B |C L - -L2-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. One load of P=34 kips is applied to the assembly at A, two loads of Q=25 kips are applied at B, and two loads of R=37 kips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 16 ksi. The normal stress magnitude in steel rod (2) must be limited to 32 ksi. The normal stress magnitude in brass rod (3) must be limited to 24 ksi. Determine the minimum diameter (in in rounded to the nearest thousandths) required for rod 2.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. One load of P = 30 kips is applied to the assembly at A, two loads of Q = 20 kips are applied at B, and two loads of R = 35 kips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 15 ksi. The normal stress magnitude in steel rod (2) must be limited to 33 ksi. The normal stress magnitude in brass rod (3) must be limited to 22 ksi. Determine the minimum diameter required for each of the three rods. (1) R В D di in. d2 = i in. dz = i in.
Bar A has diameter 'd' and bar B has diameter '2d'. Both are of the same length and are of the same material. If they are subjected to same axial load P, the ratio of extension of bar A to B is (B) 2 (A) 4 (C) 0.5 (D) 0.25
A hollow titanium [G = 43 GPa] shaft has an outside diameter of D = 46 mm and a wall thickness of t = 1.23 mm. The maximum shear stress in the shaft must be limited to 118 MPa. Determine: (a) the maximum power P that can be transmitted by the shaft if the rotation speed must be limited to 22 Hz. (b) the magnitude of the angle of twist in a 830-mm length of the shaft when 17 kW is being transmitted at 9 Hz. Answers: (a) P = (b) = i kW. O
The plate has a thickness of 20 mm and the force P = 5 kN acts along the centerline of this thickness such that d = 150 mm. (Figure 1) Figure d‡ 200 mm a 1 of 1
A hollow aluminum tube used in a roof structure has an outside diameter d2= 112mm and an inside diameter d1= 80mm. The tube is 2.80m long, and the aluminum has a shear modulus of G= 28GPa.a. If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist, in degrees,when the maximum shear stress is 52MPa?b. What diameter d, in mm, is required for a solid shaft, as shown, to resists the same torque with the same maximum stress?c. What is the ratio of the weight of the hollow tube to the weight of the solid shaft?
The following composite shaft is loaded as shown in the figure. The AC segment of the shaft is solid; it is connected to the hollow shaft CD with the help of a rigid flange at C. A torque of 100 Nm is applied at B, as shown. A uniformly distributed torque of 200 Nm/m is applied over the entire length of CD (2m), also shown in the figure. Please ignore the thickness of the rigid flange at C. Given: GAC = 140 GPa, diameter of AC = 20 mm. GCD = 200 GPa, inner diameter of AC = 40 mm, outer diameter of AC = 50 mm. a. Determine the absolute maximum shear stress on the shaft. Specify where it occurs along the length of the shaft and on the circumference of the shaft. Draw the state of stress on a volume element corresponding to the maximum absolute shear stress location. Show proper perspective when drawing the state of stress. b. Determine the absolute maximum shear strain on the shaft. Specify where it occurs along the length of the shaft and on the circumference of the shaft. Be careful…
The solid shaft, made of three different materials, carries the two torques shown. (a) Calculate the maximum shear stress in each material. (b) Find the angle of rotation of the free end of the shaft. The shear moduli are 28 GPa for the aluminum, 83 GPa for steel and 35 GPa for bronze. Aluminum 100 mm -3 m- 4 kN.m Steel 75 mm -2 m 1.5 kN - m Bronze |--15m-l
Solve it
Q1