327. A flanged bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm in outside diameter and 90 mm in inside diameter. If the allowable shearing stress in the shafts and the bolts is 60 MN/m2, how many 10-mm-diameter steel bolts must be used on a 200-mm-diameter bolt circle so that the coupling will be as strong as the weaker shaft?

327. A flanged bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm in outside diameter and 90 mm in inside diameter. If the allowable shearing stress in the shafts and the bolts is 60 MN/m2, how many 10-mm-diameter steel bolts must be used on a 200-mm-diameter bolt circle so that the coupling will be as strong as the weaker shaft?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.6.3P

See similar textbooks

Similar questions

Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
The double T-beam is fabricated by welding the three plates together as shown. Part A Determine the shear stress in the weld necessary to support a shear force of V=78 kN�=78 kN.
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A 100x100x10mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN applied along its centroidal axis which is 28.7 mm above the short leg as shown in the figure. Use an 8 mm fillet weld with a minimum tensile strength Fu=483.33 MPa. Fv = 0.30 Fu Questions: a) Determine the length of a transverse fillet weld along the edge of the angle in order to avoid eccentricity of loading. b) Determine the length of side fillet weld required at the heel. c) Determine the length of side fillet weld required at the toe.
The bolted connection shown must support an applied load of P = 5300 kN. The average shear stress in the bolts must be limited to 250 MPa. Determine the minimum bolt diameter that may be used in the connection. Answer: Minimum bolt diameter = i mm
A bearing type connection is shown in Figure 3.19. The diameter of A 325 bolts is 22 mm and the A572 Grade 50 plate material has a width of 150 mm and thickness of 16 mm. Assume diameter hole to be 24 mm. Bolt threads are excluded from the shear plane. Allowable stress of A 325 bolts: Fv = 207 MPa Fp = 1.5 Fu (to prevent excessive hole deformation) Allowable stresses of A572 Grade 50 plate material: Fy = 345 MPa Fu = 450 MPa a. Compute the tensile capacity due to the failure of the plates. b. Compute the tensile capacity due to the failure of the bolts.
Steel, connections,
Please answer this question asap!
The following image shows a front and side view of the column connection. The bolts have a diameter of ¾”. The W12X65 profile has a thickness of 0.605”. Determine:a. The shear stress in the bolts.b. The axial stress in the bolts.c. The support stress in the W12X65 profile.
Determine the design tensile strength of the 12 in. x 1/2 in. steel plate shown in the figure. The bolts are 3/4 in. diameter. The steel is A572 Gr. 50. Check yielding and fracture. Check Block Shear. T 3in. 73im 13in 1 3in t
choose letter of correct answer
A flanged bolt coupling is used to connect a solid shaft 100 mm in diameter to a hollow shaft 100 mm in outside diameter and 90 mm in inside diameter. If the allowable shearing stress in the shafts and in the bolts is 53 MPa, how many 16 mm-diameter steel bolts must be used on a 300 mm-diameter bolt circle so that the coupling will be as strong as the weaker shaft? This is an exception to our two decimal rule -- so our answer here must be rounded to the NEXT whole number.
A 3/4 in (thickness) X 5 in (height) steel plate is connected to another one through two bolts of nominal diameter 1/2 in in a zig-zag arrangement as shown. Determine the tensile strength capacity Pu of the connection. Review the three limit-states: (a) yielding in the gross area, (b) rup- ture in the overall net tensile area, and (c) block shear strength.