3. Two wooden members of 5.5" x 3.5" rectangular cross-section are joined as shown below (along the 20 degree plane). The maximum allowable stress in the joint is 100 psi in tension (perpendicular to the splice) and 80 psi in shear (parallel to the splice). What is the largest load, P, that can be applied?

3. Two wooden members of 5.5" x 3.5" rectangular cross-section are joined as shown below (along the 20 degree plane). The maximum allowable stress in the joint is 100 psi in tension (perpendicular to the splice) and 80 psi in shear (parallel to the splice). What is the largest load, P, that can be applied?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the stresses in two segments of the bar shown. Segment A has a diameter of 1 and1/4 inches and segment B has a cross-section 2in by 2in
What is the magnitude of the compressive force on the left plumb in kN? F1 the steel and the left column concrete are bonded, what is the deformation due to applied load? part 3 is pictured
Using the methods of joints, determine all the zero-force members of the fink roof truss shown in the figure below. Assume all joints are pin connected. 10 2 kN B 5 kN G F D E
Question-02Describe the various types of stresses developed in the shaft AB due to load P acting at the end C as shownin Figure 1.
Three plates are welded together to form the section shown. Dimensions of the cross section are b = 3.6 in., d = 10.8 in., a = 3.2 in., and t = 0.4 in. For a vertical shear force of V = 39 kips, determine the shear flow through the welded surface at B
For the casting shown, determine the largest couple M that can be applied without exceeding either of the following allowable stresses: gall = +8.5 ksi, all = -12.5 ksi. 0.5 in. 5 in. 2 in. 0.5 in. 3 in. 0.5 in. The largest couple M that can be applied without exceeding either of the following allowable stresses is kip.in.
The figure below are cables ( circular section) supporting a MN kN. Find the axial stress of each. Thecables has a limited working stress of SN mPa. What will be the required diameter of each cables tosupport the MN kN load? complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94
Three plates are welded together to form the section shown. Dimensions of the cross section are b = 6.0 in., d=18.0 in, a = 3.3 in., and t= 0.8 in. For a vertical shear force of V = 45 kips, determine the shear flow through the welded surface at B
S9. Knowing that the allowable normal stress for the steel used is 150 MPa, select the most economical metric wide-flange beam to support the loading shown in Figure 9.0. 50 kN/m A D B -2.4 m- 0.8 m 0.8 m Figure 9.0 $10. Determine the average shearing stress in the web of the beam indicated and check whether the design obtained earlier for that beam is acceptable, knowing that the allowable shearing stress for the steel used is 110 MPa. Consider the beam of $9 above.
Required information Consider the loading shown. The allowable normal stress for the steel used is 160 MPa. 0.8 m 50 kN/m B -2.4 m- 0.8 m For the selected design, determine the actual value of Om in the beam. (Round the final answer to one decimal place. You must provide an answer before moving to the next part.) The actual value of om in the beam is 160 MPa.
Three planks are connected as shown by bolts of 15-mm diameter spaced every 200 mm along the longitudinal axis of the beam. For a vertical shear of 10 kN, determine the average shear stress in the bolts. 100 mm 125 mm 125 mm 100 mm 300 mm
1. Figure shows two wood members are joined together using a 60 degrees wood glue adhesive. Find the average normal and shear stress resisted in the plane of the connection. 25 mm 8 kN- 8 kN 60° 30 mm