Three plates are welded together to form the section shown. Dimensions of the cross section are b = 3.6 in., d = 10.8 in., a = 3.2 in., and t = 0.4 in. For a vertical shear force of V = 39 kips, determine the shear flow through the welded surface at B Three plates are welded together to form the section shown. Dimensions of the cross section are b = 3.6 in., d = 10.8 in., a = 3.2 in., andt = 0.4 in. For a vertical shear force of V = 39 kips, determine the shear flow through the welded surface at B.yZ-dAВb bAnswer:kip/in.%D

Given data, a = 3.2 in b = 3.6 in d = 10.8 in t = 0.4 in V = 39 kips To Find out the shear flow…

Three plates are welded together to form the section shown. Dimensions of the cross section are b = 3.6 in., d = 10.8 in., a = 3.2 in., and t = 0.4 in. For a vertical shear force of V = 39 kips, determine the shear flow through the welded surface at B. A B a b. b. Answer: qB = i ! kip/in.

Three plates are welded together to form the section shown. Dimensions of the cross section are b = 3.6 in., d = 10.8 in., a = 3.2 in., and t = 0.4 in. For a vertical shear force of V = 39 kips, determine the shear flow through the welded surface at B. A B a b. b. Answer: qB = i ! kip/in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please box the final answer
Determine the length of tension anchorage required for the 36 mm diameter plain mild steel reinforcing bars in the canrilever of figuer below. The charactersitic material strengths are feu-30N/mm² and fy=250KN. The ultimate anchorage bond stress. Stress, fou-1.5N/mm² Anchorage length R25 bars
GIVEN: Solid alumınum bar shown: 4 in. by4 in. E = 10 x 10° psi oy = 36 ksi 4000 2000 1b 4000 16 B 12' REQ’D: A) Load in each section of the bar (state whether C or T) PAB = Pac PCD = B) Maximum axial stress in the bar. In which section does this occur? C) Final length of the bar
Determine stress in segment AB
Please kindly give me a,b,c and d answers..help me. Urgent Thank you
b FIGURE P1.38/39. P1.39 (WP Two aluminum plates, each having a width b = 5.0 in. and a thickness t = 0.75 in., are welded together as shown in Figure P1.38/39. Assume that a = 2.0 in. Specifications require that the normal and shear stress magnitudes acting in the weld material may not exceed 35 ksi and 24 ksi, respectively. Determine the largest axial load P that can be applied to the aluminum plates.
The pin in the image shown below must transfer an axial tension force of 12.7 kN. Calculate the minimum pin diameter. Use Shear stress-D0.4"Yield strength. Assume material is 1020 hot-rolled steel. * P2 Shear Planes Pin
Y1
Problem 3: Find the design moment strength for the following section: f'e = 6000 psi hf=6" T a. Mn = fy =60 ksi Es = 29,000 ksi b = 24" 8" bw = 4" bw=4" k-ft A's = 2 in² As = 6.5 in² (total) d` = 1.5" d = 30" Strain Stress
* A 76 mm x 76mm x 6mm angular section is welded to a gusset plate having a thickness of 8mm as shown in the figure. The length L1 equals 125mm and L2 is 65mm. The angular section has a cross sectional area of 929mm2, Fy=248 MPa, Fu=400MPa. Determine the value of tensile force P based on block shear in gusset plate along the weld in kN. Allowable stresses: Allowable tensile stress (gross area) = 0.6Fy Allowable tensile stress (net area) = 0.50Fu Allowable shear stress (net area) = 0.30Fu P gusset plate L₂= 65 mm 25 mm
SOLVE COMPLETELY. SHOW COMPLETE SOLUTION, INCLUDE FBD
A flexural member is fabricated from two flanges plates 1" x 20" and a web plate 1/2" x 22". The yield stress of the steel is 36 ksi. a. Compute the elastic modulus and the yield moment with respect to major principal axis. b. Compute the plastic modulus and the plastic moment with respect to major principal axis.