Determine the stress in members BD, DE and EG of the truss shown if the diameter of each cross-section is equal to 2.5cm. State whether each member is in tension or compression. 145 EN 4m- 4.5 m Match each item to a choice: OEG OBD ODE

Q: 1. The figure shows a roof truss and the detail of the connection at joint D. Member DE is angle…

A:

Q: Solve for the forces at all members of the truss shown below. Identify if the member is in tension…

A: Solution: Using equilibrium condition: ΣFx=0Ax=280 kNΣFy=0Ay+Gy-150-150=0Ay+Gy=300 Taking moment at…

Q: A built-up section shown, 30 feet long, is fixed at both ends and braced in the weak direction at…

A: Given data:Section properties-

Q: A flexural member is fabricated from two flanges plates 1" x 20" and a web plate 1/2" x 22". The…

A:

Q: The linkage supports a force of 500 lb and rides along the top and bottom flanges of the crane rail.…

A: In the image, the object of interest is the linkage. We can see that the linkage is supported by a…

Q: PROBLEM 2: Determine the smallest safe cross-sectional areas, in mm², of members Cl and CD for the…

A: Given: The working stress in tension is 10 MPa. The working stress in compression is 8 MPa. Consider…

Q: AW18 × 40 standard steel shape is used to support the loads shown on the beam. Assume P = 20 kips, w…

A: Given Data: Load=p=20 kips w=5.8 kips LAB=4.0 ft LBC=4.0 ft LCD=13 ft

Q: Horizontal and Vertical of F •Force member BE, ED, and CD •Resultant support reaction at A -Include…

A: To find reaction at support

Q: Determine the forces in all the members, and state if these members are in tension or compression.…

A: Given data  Span length  Vertical loading  Horizontal loading.    At joint D only two members are…

Q: 2. A vertical member of a steel truss is subjected to a live load of 25 kN and a service dead load…

A: LL = 25 kNDL = 50 kNU = 1.0Plate dimensions: 10 x 100 mmFactored load:P = 1.2 DL + 1.6 LL = (1.2x50)…

Q: Determine the kind of amount of stress in members of the truss shown by the method of joints or…

A:

Q: Problem 1: The truss shown below is made of fiberglass member section and an axial strength of 14…

A: Given : Axial strength = 14 MPa dia of high strength nylon pins = 20 mm Shear strength = 25 MPa…

Q: Problem For the frame shown, design the maximum permissible value of P with a factor of safety of…

A:

Q: Consider the truss shown in (Ecure 1). Suppose that Fi-60 kN and F₂-25 kN Figure ▼ 40 kN Part C FGH…

A: To Determine Force in the memeber ED , EH & GH.

Q: ure 2m B 2m C 2 m D 4 m. 500 N 700 N 2 of 2 Identify the zero-force members in the truss shown in…

A: Given truss member:

Q: A PL40 mm X 250 mm (smaller member) is connected to a gusset plate (bigger member) as shown. The…

A:

Q: Estimate the cross-sectional area of a 350S125-27 cold-formed shape. a. If the member is tested in…

A: Consider the given data Cross sectional area=0.173 in2Yield strenght, σy=225 Mpa=33 ksi