Estimate the cross-sectional area of a 350S125-27 cold-formed shape. a. If the member is tested in tension, what would be the maximum force thesample could carry before reaching the yield strength if the steel has ayield strength of 225 MPa?b. Would you expect a 2.5 m stud to carry the same load in compression?(explain)

Q: Delermine the average normal stress in the aluminum due to this loading The A-36 steel pipe in…

A: Determine stress in steel and aluminium

Q: Regular low-alloy steel has an allowable shearing stress of approximately 20.0 ksi (Fv = 20.0 ksi).…

A: Answer  In order to check the adequacy of given beam for allowable shearing stress fv = 20 ksi we…

Q: Determine the tensile strength of the welded A992 WT4×20. WT4 × 20 PL - Transverse weld

A: Given:- The steel section used = WT 4×20 The steel used = A992  To determine:- The tensile strength…

Q: The following steel member is connected to the gusset plate via two longitudinal welds. The width of…

A: Width of the member = 58 mm Length of the weld = 87 mm Yield Stress fy = 300 MPa Ultimate Stress fu…

Q: The assembly is used to support a 10 kN point load at the tip as shown. The steel rod has a diameter…

A:

Q: A flanged bolt coupling has ten 12-mm di ameter steel bolts on 500 mm diameter b olt circle and six…

A: Step 1: Calculate the shear area per bolt: Steel bolts: A = π * (12 / 2)2 = 113.1 mm2 Aluminum…

Q: ISA 75 x 75 x 8 mm serves as tensile member. This angle is welded to a gusset plate as shown in…

A: Note : This question is related to Indian Standard Code as asked in the problem. Given data,  ISA…

Q: The pin in the image shown below must transfer an axial tension force of 12.7 kN. Calculate the…

A: First we need to find the value of yield strength using steel through internet.

Q: afe strength of a 5/16 in. fillet weld if it's actual length is 3 1/2 in. and the allowable unit…

A:

Q: A rectangular steel plate is subjected to an axial dead load of 30 kips and a live load of48 kips.…

A: Dead load = Ld = 30 kips   Live load = Ll = 48 kips   Yield strength = σy = 36 ksi   F.O.S = f = 1.5…

Q: An I-section with two cover plates is used as tension member and is subjected to a load of 120 t…

A:

Q: Required information A square yellow-brass bar must not stretch more than 105 GPa and that the…

A:

Q: The ultimate tensile strength of mild steel is 200 N/mm2. A tie of equal legs angle section has to…

A:

Q: pecify a suitable aluminum casting alloy for a bar with square crosssection. Length of one side of…

A: Given:- The length of the one side of the cross-section= 50 mm The value of the tensile load = 60 kN…

Q: A steel bar is attached to a wood support beam with four 21 mm diameter lag screws, as shown in the…

A: Step 1

Q: A Tension member with no holes is subjected to axial loads of PD=68kN & PL=64kN.It is also subjected…

A: A Tension member with no holes is subjected to axial loads of PD=68kN & PL=64kN.It is also…

Q: A steel 4340, with tensile strength of 550 Mpa and Compressive -550 Mpa with length of 3.5 mm find…

A: Permissible maximum stress to a structural member is generally subjected, that is large enough to…

Q: In the connection shown, 1/4-in. side and end fillet welds are used to connect the 3-in.-by-1 in.…

A:

Q: The double - riveted joint connects two plates which are each 3.0 mm thick, and the rivets have a…

A: Diameter of the rivet, d = 6t = 63 = 10.39 mmPitch of the rivets, p = b mmFailure strength of the…

Q: 1.12 A fillet-welded joint of 6 mm size is shown in the figure. The welded surfaces meet at 60-90…

A:

Q: A 750-MM SHAFT IS COMPOSED OF STEEL AND ALUMINUM PARTS. DETERMINE THE CENTROIDAL Y (IN MM) OF THE…

A: Given,

Q: Situation 5. The angular section shown below is welded to a 12 mm gusset plate.. Both materials are…

A: The given data is as follows : Size of angular section = 150 x 90 x 12 Area of angular section =…

Q: 2. A column HP 14 x 102 of A572 Gr. 55 steel has a length of 15 ft is fixed at both ends. Compute…

A:

Q: A 250 mm long rod with a 15×30 mm cross section consists of a brass layer joined by welding in the…

A:

Q: 2- The Tensile stress of AISI 1035 Cold-dra (a) 550 MPa. (b) 500 MPa. (c) 450 MPa.

A: AISI stands for American Iron and Steel Institute- AISI 1035 is a water resistance carbon steel.…

Q: A storage tank of air, 30 inches in diameter, is to withstand an internal pressure of 180 psi with a…

A: Given:- d=30 inches internal pressure=180 psi design factor=3.5 C1020 annealed relative strength=92%…

Q: A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig. p-211. Axial loads…

A:

Q: AN ALUMINUM SEGMENTS HAVING A DIAMETER AND LENGTHS SHOWN IN THE FIGURE. IF E= 85 KPa, COMPUTE THE…

A: Given data in question  Load Diameter  Length  Elasticity modulus  To find out  Elongation

Q: This is the corresponding tensile stress (MPa) at the minimum strain (as allowed by NSCP2015) of…

A:

Q: 2. A steel plate is 360 mm wide and 20 mm thick with four bolts hole into the place as shown in the…

A:

Q: A mild steel flat of width 120 mm and thickness 10 mm is bent into an arc of a circle of radius 10 m…

A: Width of mild steel flat b=120 mm,Thickness t=10 mm,Radius R=10 m,To Find-The value of the pure…

Q: What will be the tensile strength due to rupture of critical section of an angle section ISA 150 x…

A:

Q: The member shown A572 Grade SU Length of Properties: Pn = 330kn cb=1.06 Mn = 515 column is kn.m is…

A: