3. Sketch the phasor diagram of the magnitude of the rms input voltage Vs and the magnitude of the rms voltage across the inductor VL in the circuit shown below. Clearly indicate the magnitude and phase relationship on your sketch. The component values shown are all nominal values. (20 pts) + ΚΩ 2 volts rms 150 Hz Vs 100m H. VL

3. Sketch the phasor diagram of the magnitude of the rms input voltage Vs and the magnitude of the rms voltage across the inductor VL in the circuit shown below. Clearly indicate the magnitude and phase relationship on your sketch. The component values shown are all nominal values. (20 pts) + ΚΩ 2 volts rms 150 Hz Vs 100m H. VL

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
Give a detailed solution. Please need help
Thanks for answering this question
An inductor, a capacitor, and a resistor are connected in parallel with a function generator. The inductor draws 100mA RMS, the capacitor draws 150mA RMS, and the resistor draws 200mA RMS. Find the magnitude of the total current.
Given a capacitive load absorbing 5 kW with a power factor of 0.85. The source connected to this load is an AC voltage supply with 120V RMS at a frequency of 50 Hz. Please find; A) Peak current (m) and RMS Current (ms) Values B) Draw peak voltage and current phasors on phasor diagram with everything labelled C) Find the value of an inductor that when connected in parallel will improve the power factor to 0.95.
i need help with part c
A certain impedance is given by 1012° N. Does the current lead or lag the voltage, and by how many degrees? Fill in the blanks. The current the voltage by
Please help with the solution.
b) Determine the voltage ?(?) and current ?(?) sinusoidal forms. Sketch one cycle of the waveforms in the same x-axis. Clearly indicating the peak value and the period of each waveform and the phase difference (in milliseconds) between the two waveforms. c) Determine the values of resistance R and inductance L. d) Determine the phasors ?L, ?r and ?c. e) Sketch the phasor diagram showing ?s, ?r, ?r, ?c and ?.
Please answer alll subparts for like either dislike...
Determine the values of resistance R and inductance L. need help on question C ，urgent