Project Homework: Create a simulation for a tank when the flowrate inside and outside the tank must range between 0 and 10 lit/s: 1) The level should be controlled within a range between more than zero to 1000 lit. 2) An alarm must be launched when the level is out of range (less than 100 and more than 900 lit). 3) When the capacity reaches to the maximum the motor turns OFF. Qin h C Qout area=A solve in lab view

Project Homework: Create a simulation for a tank when the flowrate inside and outside the tank must range between 0 and 10 lit/s: 1) The level should be controlled within a range between more than zero to 1000 lit. 2) An alarm must be launched when the level is out of range (less than 100 and more than 900 lit). 3) When the capacity reaches to the maximum the motor turns OFF. Qin h C Qout area=A solve in lab view

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

You are working as an electrician in a large steel manufacturing plant, and you are in the process of doing preventive maintenance on a large DC generator. You have megged both the series and shunt field windings and found that each has over 10 M to ground. Your ohmmeter, however, indicates a resistance of 1.5 across terminals S1andS2. The ohmmeter indicates a resistance of 225 between terminals F1andF2. Are these readings normal for this type machine, or is there a likely problem? Explain your answer.
If the charging resistor was twice as large as the discharging resistor in Figure 4, theamplitudes of the charging and discharging waveforms would be ________.a. The sameb. Different
ANSWER ASAP PLS
Answer only 2.
hey please provide answers to all questions. I definitely give an upvote Answer all with brief explain if not i will dislike..
HUMBER CENG 150 Electronic Circuits Lab 3- Bridge Rectifier and Capacitive Filtering QUESTIONS: 1. A transformer is rated at 120V primary/23V secondary. What peak to peak secondary voltage would be displayed on a scope on the secondary side? Show all your calculations. 2. The % ripple is calculated as % of Ripple -- Vipep Average Voc x 100% Determine the % ripple for both capacitors used in the experiment. Show all your calculations. % Ripple (10 uF) = % Ripple (100 µF) - Page 3 of 3
Electronic communications field i need for my today class work please give me details information
Read and Solve carefully please Write clearly and Box the Final answer Hint : Enter your answer to the 2nd nearest decimal place in percent.
Power half wave rectifier
A dc series motor is running at rated speed without any additional resistance in series if an additional resistance is placed in series, the speed of motor a) Increases C ocillates around the rated speed O decreases O remains unchanged O
03. A) Design a multi range d.c. mille ammeter using a basic movement with an internal resistance Rm 50 ohm and a full scale deflection current Im-1mA. The ranges required are 0-10mA; 0-50mA: 0-100mA and 0-500mA. B) The pointer of a moving coil instrument gives full scale deflection of 20mA. The potential difference across the meter when carrying 20mA is 400mV.The instrument to be used is 200A for full cale deflection. Find the shunt resistance required to achieve this, if the instrument to be used as s Itmeter for full scale reading with 1000V. Find the series resistance to be connected it?
A copper-oxide rectifier and a non-inductive resistance of 20 Ω are connected in series across a sinusoidal a.c. supply of 230 V (r.m.s.). The resistance of the rectifier is 2.5 Ω in forward direction and 3,000 Ω in the reverse direction. Calculate the r.m.s. and average values of the current. Answer: [r.m.s. value = 5.1 A, average value = 3.22 A]