2. For the simply supported beam shown below, a. Find reactions at A and D b. Sketch the V-M diagrams. 2m E B 2m 2m 2m F 14 KN C 10 KN 2m D

Q: need help with part b i solved a prior

A: ◆ The mean effective pressure: 562.94 kPa. ◆ The indicated power developed by the engine is 4.10 kW.…

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: In the figure shown, gear A rotates at 300 rpm. Gear S is fixed and has 80 teeth. The three…

A: Write the given data. Speed of arm, Narm=180 rpmSpeed of anulus gear, NA=300 rpmSpeed of gear S,…

Q: Ax R.70 4x 1.40 B This part contains 4 holes with radius 0.375 inches 1.00 This part contains 4…

A: Select the correct statement about the notation circled in green and marked as letterA. Assume all…

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: You are given two shafts of equal lengths and made from the same material: a hollow shaft, with an…

A:

Q: If the 45 degree offset distance at point B is 8 inches, the "travel" distance (center to center)…

A: It is given that the offset is 45 degrees and it is needed to determine the center to center…

Q: Question Figure Q1 shows the schematic diagram of a moulding press, which is driven by a crank BC…

A: Figure Q1, shows the schematic diagram of a moulding press, which is driven by a crank BC rotating…

Q: Question Figure Q1 shows the schematic diagram of a moulding press, which is driven by a crank BC…

A: Figure Q1 shows the schematic diagram of a moulding press, which is driven by a crank BC rotating…

Q: Through load analysis, force and moment diagram are obtained, as shown below. Diagram below shows…

A: The force that occurs between mating gears is normal to the surfaces in contact. The axial force Fa,…

Q: Part C - Maximum allowable axial force for fixed-and-free-end support If the cylindrical column is…

A:

Q: The objects shown below have been rotated positively about one of the axes shown. the amount of…

A: According to the given data rotation amount and rotational axis is provided in the below picture.

Q: QUESTION 2 A shaft rotates at 300 rpm. 1), If it carries a spur gear that delivers 5 hp to a mating…

A: Given: N=300 rpm

Q: solve a thru e show all steps

A: is normal reaction force between contacting surfaces.W is the weight force of the block. is the…

Q: I want to buy a two METAL SPUR GEAR for my 2 pieces of G.I pipe with an 3 inches diameter (3mm…

A:

Q: Gear 2 in the diagram below is driven at a speed of 126 revolutions per minute. Gear 2 has 16 teeth,…

A: The gear train is simple,The speed ratio of a simple gear train with 2 gears is as follows,Here,N is…

Q: For practical working gears as manufactured, typically the addendum, a, is larger than the dedendum,…

A: Addendum: The distance between the top land and the pitch circle on a gear tooth, is called as…

Q: f e (D d b C a k j a=38.0 b=41.5 c=39.3 d=40.1 e=55.8 f=39.4 q=36.7

A: a = 38.0b = 41.5c = 39.3d = 40.1e = 55.8f = 39.4g = 36.7h = 65.7i = 49.0j = 50.0k = 61.9l = 7.8m =…

Q: The two gears in the picture below on the left are meshing together. The two gears in the picture on…

A: A-The two meshing gears have the same module. When two gear meshes, the module (which is defined as…

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.