2. Determine the state of stress at point H. Each section of the pipe has an inner and outer diameter of 36 mm and 44 mm, respectively. Indicate your final answers on the given volume element. Be sure to clearly indicate the direction of your assigned internal loadings in a valid FBD. 200 N 225 225 150 N 300 175 100 N 100 N 100 N Dimensions in mm

2. Determine the state of stress at point H. Each section of the pipe has an inner and outer diameter of 36 mm and 44 mm, respectively. Indicate your final answers on the given volume element. Be sure to clearly indicate the direction of your assigned internal loadings in a valid FBD. 200 N 225 225 150 N 300 175 100 N 100 N 100 N Dimensions in mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the equivalent state of stress on an element at the same point that represents the principal stresses at the point. Also, find the corresponding orientation of the element with respect to the element shown.
Determine the shear stress of the cylinder pivot pin (φ25mm). The clamping force of the pliers is 6000N. The dimensions of the structure are: X1 = 10 mm X2 = 120 mm Y1 = 110 mm Y2 = 798 mm Use the units [N, mm], ie the answer comes in MPa !!! Please enter a numeric value only !!
please answer quickly and show a complete solution and what is the correct answer
Solve it correctly please. I will rate accordingly.
Mohr's cirde is shown for a point in a physical object that is subjected to plane stress. Each grid square is 24 MPa in size (a) Determine the stresses 0, 0, and the magnitude of Ty and show them on a stress element (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (eg, see Figure 12.15 or Figure 1216).
From 3 forces, 2 bending moments and 1 toque acting on B, which ones are non zero, and the direction they are acting. Then indicate if they make shear or normal stress Draw 3-d stress state cust above plane a
You must answer all questions.
Calcuate torsion From Point A to Point C, Calcuate Bending From Point A to Point B and Point A to Point C. Draw a FBD from point A to point B and another for point A to C indicating what stresses are been calculate. Use the stress tensor and stress cube to Indicate what forces are acting at point A. Force apply at point B is 70lb Distacen from Point A to B is 12 in or 1 feet long Distacen from Point A to C is 3 in Handle diameter 0.625 in
4
For the element shown below, determine: 1- The principal stresses and the maximum in-plane shear stress acting at the point by using equations, then show these stresses on an appropriate sketch. 2- The normal stresses 0 n and ¢ t and the shear stress T nt for element oriented 20° clockwise from the position shown, using Mobhr’s Circle. 75 MPa
Calcuate torsion From Point A to Point C, Calcuate Bending From Point A to Point B and Point A to Point C. Draw a FBD from point A to point B and another for point A to C indicating what stresses are been calculate. Use the stress tensor and stress cube to Indicate what forces are acting at point A. Force apply at point B is 70lb Distacen from Point A to B is 12 in or 1 feet long Distacen from Point A to C is 3 in Handle diameter 0.625 in
The cross-section of bar ABCD is made of a triangle with sides equal to 15 mm, 12 mm, and 10 mm. Determine the maximum normal stress in the bar. Express o in MPa and round off your answer in 2 decimal places. Please answer this one