Part AThe state of stress at a point in a member is shown on theelement. Suppose that oe = -50 MPa, oy = -100 MPa., Tzy = -29 MPa.Determine the normal stress component acting on the plane AB.(Figure 1)Express your answer with the appropriate units.HÁ?Figure3 1 of 187.614MPaOe =ASubmitPrevious Answers Request AnswerX Incorrect; Try Again; 5 attempts remaining30Part BDetermine the shear stress component acting on the plane AB.ВExpress your answer with the appropriate units. The state of stress at a point in a member is shown on theelement. Suppose that o, = -50 MPa , oy = -100 MPaSubmitPrevious Answers Request AnswerTey = -29 MPa.X Incorrect; Try Again; 5 attempts remainingPart BFigure< 1 of 1Determine the shear stress component acting on the plane AB.AExpress your answer with the appropriate units.σ.HẢ?xy30%ValueUnitsSubmitRequest AnswerВProvide Feedback

We have to find out the normal & shear component of force acting on the plane

Answered: Determine the normal stress component…

Engineering

Mechanical Engineering

Determine the normal stress component acting on the plane AB. (Figure 1)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate non-zero stress components (normal and shear) at points A, B and C. Point C is located at the center of the cross section attached to the wall. Calculate non-zero strain components at point B. Neglect shear stress due to shear force. Given: loading F = 400 N, P-2000 N, and T = 75 N·m, Young's modulus E = 70 GPa, Poisson's ratio v = 0.25 15-mm D. -100 mm
5. The general stress element is loaded such that σx = 50 MPa. Using Mohr’s circle, find out the maximum normal stress and shear stress acting on this element. (Simple tension)
Please help me answer this asap thank you
The cross-sectional area of the prismatic bar is 0.02 m². If the normal and shear stresses on the plane P are d = 1.25 MPa and Te = -1.5 MPa, what are the angle and the axial force P. Figure 1
The principal strains at a point on the aluminum surface of a tank are P1 = 630(10-6) and P2 = 350(10-6). If this is a case of plane stress, determine the associated principal stresses at the point in the same plane. Eal = 10(103) ksi,nal = 0.33.
The stresses in a 2-D rectangular steel body (E = 200 GPa, v=0.32) are xx = -A(L - x)y, and oxy = A(h² - 4y²); other stress components are zero. Here, L represents length and h is height. What is the strain component y xy A - (h² - y²) 8E O A A 8G - (h²-x²) - (h²-x²) 8E А A= (h²-y:²) 8G ?
The solid shaft is fixed in the wall at A (Figure Q2). A force F is applied at B, determine a) the stress components at points D and E, b) the principal stress at each of these points. (Draw free body diagram to show all loading forces and moments) Take F = 12 N and 0 = 45°. 1,25 mm 6 mm. 8 mm. 3 mm B F Figure Q2
a. At a point in a given material the three dimensional state of stress is given by ox = oy oz = 10 MPa ,Txy F 20 MPa, tyz = 10 MPa. Compute the principle planes if the 37.3 MPa, o2 %3D TXZ %3D corresponding principles stresses are, ol 10MPA, o3 = 2.7 MPa %3D %3D
(1) Given: b₁ B P=28 kN Square Bars b₁ = 57 mm (2) Q =9 kN b2 C b₂ = 19mm (3) Q R = 38kN ↑ D b3 = 38mm R WHAT IS THE AXAIL STRESS IN BAR 2? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES. POSITIVE FOR TENSILE STRESS AND NEGATIVE FOR COMPRESSIVE STRESS.
-8 in.- -8 in.- (a) (b) Which of the following best explains why cylinder (b) has a higher longitudinal stress in its walls compared to cylinder (a)? Assume the gauge pressure of the fluid inside the cylinder is non-zero. O Cylinder (b) is supported at two locations Cylinder (a) is not free to deform in its longitudinal direction The vertical (longitudinal) pressure in cylinder (a) is transferred directly to the [bottom] support, bypassing the cylinder walls None of the above the longitudinal stress for both cylinders is the same
i need the answer quickly
For the problem shown in the figure,- Find the axial displacement at the end B- Determine the variation of stress along the axis of the bar.GIVEN: E=50 N/mm2 , d1 = 4 cm, d2 = 6 cm, L = 80 cm, t = 6 mm, F = 1000N