2) a) Plot the voltage transfer characteristic of the circuit below. Assume diode and zener areideal with VDon=0V (20Pts)view1K1, B-100, VBE =0,7VovoVCEsat = 0V,2KIt10 V8V zener

Answered: 2) a) Plot the voltage transfer…

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is the difference between a diode and rectifier?
Draw the corresponding output waveform of the double diode partial limiter below using simplified diode model. Indicate all the necessary voltage levels and use Silicon diodes. 20 VP-P 1KQ M D1 9V D2 4.5V VOUT
2.Sketch the waveforms for the load current and load voltage for the circuit show in Figure 2. Show the peak values. Use the offset diode model in your calculations. Input voltage source could be represented as a sine waveform, given as Vin=20sin(wt +30), and RL = 20 S Figure 2 www R₁ Vout
Draw the changes in Vi and Id of the ideal diode half-wave rectifier circuit in the figure. The frequency of the sine signal here will be taken as 50Hz. (Changes in Vi and Id will be drawn!!!)
In the clamping circuit below, assume the diode has Von-0.7V and V₁ is a sinusoidal wave with a peak-to-peak amplitude of 10V. How much is the maximum value of the output voltage signal (Vmax)? And how much will it be if we set V₂=2V? Input V1 C1 0.1e-6 9.3 V and 7.3 V 9.3 V and 11.3 V 11.3 V and 7.3 V O 7.3 V and 12.0 V O 12.0 V and 7.3 V Output D1 1N4148 .tran 30-3 V2 0 Vmax V(output) 0.0ms putput MAN Input 0.6ms 1.2ms V(input) 1.8ms 2.4ms 3.0ms
1. Draw the output voltage waveform for each circuit in Figure below and include the voltage values. N +5V +50V Vin R Va R o 0% Y 9 33k 5 Vo -5V -50v I I (@ () a. Whatis the peak inverse voltage across each diode in Figure above? b. What is the peak forward current through each diode in Figure above?
4) Consider the following circuit. Assume that the diodes are modeled with constant offset models with Von = 1V and that the input waveform shown is applied. Sketch the corresponding waveform for Vo. Label peak values. You do not need to show your work. Vin Vin 10 -10 1K 5V D1 Vo D2
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
Sketch the output waveform and indicate the expected voltage levels for each of these diode circuits below. Use the diode models as indicated.
For the circuit in the figure, let V input = 8V, Ri = 12ohms, RL = 10ohms, and VZ = 3.3V. Determine the voltages and currents of the resistors and the current of the zener diode.
Using an ideal diode, design a clamper circuit that result in the desired output waveform as shown in Figure Q7. Show overall analysis to justify the proposed design. 7. Vo Vi Designed Clamper Circuit - 3 V -20 - 43 V - Fiqure Q7 20

SEE MORE QUESTIONS

Recommended textbooks for you

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

2) a) Plot the voltage transfer characteristic of the circuit below. Assume diode and zener are ideal with VDon=0V (20Pts) view 1K 1, B-100, VBE =0,7V ovo VCEsat = 0V, 2K It 10 V 8V zener