17. Consider the following hypothetical instruction: SubMem R1, mem1, mem2 This instruction works as follows: \[ \mathrm{R} 1 \leftarrow \text { [mem1] - [mem2] } \] In a multi-cycle datapath implementation, this instruction will: a. Use the MDR twice b. Use the ALU once c. Use the "shift to left" unit twice d. None of the above Answer: B 18. Consider the following hypothetical instruction: Mems mem1, R1, mem2 This instruction works as follows: \[ \text { [mem1] } \leftarrow \mathrm{R} 1 \text { - [mem2] } \] One of the following is correct about this instruction: a. It will not need theBregister b. It will require priting into MDR twice c. It will require writing into the ALUout three times d. None of the above Answer: A 19. By comparing the hypothetical instructions given in Questions (17) and (18), if we run these instructions on the same processor, then one of the following is correct: a. Both instructions have the same CPI b. Mems executes faster than SubMem c. SubMem executes faster than Mems d. Mems does not need the MDR please answer question 19 only

Q: 000FFDOE and %eax= 0x000FED25 (Hexade

A: The answer is..

Q: Consider a RISC-V assembly function func1. func1 has three passing arguments stored in registers a0,…

A: In RISC-V assembly programming, understanding the structure and size of stack frames is crucial for…

Q: Consider your stack contains two parameters A and C each of 4 Bytes. Give an instruction that will…

A: Stack is a linear data structure which follows a particular order in which the operations are…

Q: If this Datapath is currently executing the instruction, LW $s1, -4($t1), register s1 contains the…

A: It is defined as the Operator at the heart of the control room with its latest fully integrated…

Q: Translate the following into three address code while (A < B) do If (C< D) then X =Y+Z.

A: The Answer is

Q: An algorithm that has time complexity of O(n^2) requires 1 second to process 10 input records.…

A: As per our company policy we can attempted one question at a time if you want the answer of the…

Q: What happens if an instruction fails to get approval before writing to VA page 30? In the following…

A: Introduction: The TLB caches recent virtual memory to physical memory translations and maybe an…

Q: Suppose that a C++ int variable x is associated with register $t1. Write the MIPS I instruct…

A: Actually, register is a used to store small amount of data.

Q: Write an instruction that loads the value -185 (in decimal) in x6. Answer: Write an instruction that…

A: This is a draft of the next release of the document describing the RISC-V user-level…

Q: 7. In a normal branch instruction, we provide the number of instructions we need to go to with…

A: In a normal branch instruction, we provide the number of instructions we need to go to with respect…

Q: 3. Consider the following AT&T ISA 32 ASM codes for a C for loop: loop: pushl movl tabp teap, tebp 8…

A: To do: based on assembly code

Q: LEGv8 does not have a native mov instruction to copy the value in one register to another.  The…

A: LEGv8 is a simple version of ARMv8 instruction set. LEGv8 has a 32 × 64-bit register file n Use for…

Q: 5. Below is a depiction of a loop in instruction memory address Ox0 TOP: instruction 1 Ox4…

A: The branch target bits are in states 00,01,10 and 11 for branch not taken, partially branch not…

Q: The following code is to be scheduled and executed on a two-slot VLIW machine with the goal of…

A: The following RISC table for the given question:

Q: Q2. Refer to datapath design on slide no. 26 with added blocks for jump instructions as shown in…

A: In a datapath design with control and jumps, the datapath includes additional logic to handle branch…

Q: Implement the following operation using shift and arithmetic instructions. Assume that all…

A: a. Implement the following operation using shift and arithmetic instructions Assume that all…

Q: Will upvote! Find the memory address of the next instruction executed by the microprocessor, when…

A: Answer: We need to write the what will be the memory address of the next instruction executed by the…

Q: Registers in RISC-V are 64-bit.  For the sake of simplicity, consider the following instructions…

A: RISC-V which is an open standard instruction set architecture that are based on established RISC…

Q: use: Microchip Studio and ATmega328p Activity 3: COM instruction flags Write and assemble the…

A: Solution:   Here is the assembly code for the given program using Microchip Studio and ATmega328p:

Q: Describe the modifications to the single clock cycle datapath that would be needed to implement the…

A: A single-cycle datapath is a type of processor design in which each instruction is executed in a…

Q: In the Intel 8086 microprocessor, suppose the register AX contains the data 35AB H. What will be the…

A:

Q: Let x be an 8-bit unsigned number. What is the value of x in base 2 for which the following…

A: #include&lt;bits/stdc++.h&gt; using namespace std; typedef long long int ll; // Find position  n =…

Q: use: Microchip Studio and ATmega328p Activity 2: SUB instruction flags Write and assemble the…

A: Here is the program written in assembly language for the ATmega328p microcontroller to perform the…

Q: XCHG (BX],[DS] is a valid instruction. Select one: O True O False

A: XCHG is a instruction that is used to exchange the contents of 2 registers or 2 memory locations.

Q: The instruction format for the SHL instruction is: SHL destination, count Working with a 32-bit…

A: SHL destination, count working with 32 bit operand, what are the bounds for the count value

Q: Lab work 1: Assume you want to execute the instruction sW (store word) on the MIPS single-cycle data…

A: Datapath is the hardware that performs all the required operations, for example, ALU, registers, and…

Q: Translate the following user-level instruction to a microprogram so it can be directly executed by…

A: Hey there, I am writing the required solution of the above stated question.Please do find the…

Q: We want to design a new K-format instruction for a branch-equal-immediate. A: What information would…

A: In this question we have been asked to design a new K-format instruction for branch equal…

Q: Add control states to the following to implement an exchange-with-memory instruction, xchg. such…

A: Answers:-   The Add control states to the following and  implement an exchange-with- a memory…

Q: CCode V Consider the following Convolutional code encoder, where the initial value of all memory…

A: The correct answer is:

Q: What happens if VA page 30 is written even if an instruction was not accepted? An instance of a…

A: VA page 30 instructions: If the instructions want to write to Virtual Address (VA) page 30, they…

Q: 4. We have the following data for a branching instruction, where T = branch is taken, and N = the…

A: Branch Prediction: Requires three things to be predicted at fetch stage- Whether the fetched…

Q: Q1: Consider the following instruction: Instruction1: AND Rd,Rs,Rt Instruction 2: SUB Rd, Rs, Rt

A: a ) ALU Operation is AND,BSrc will look to register,OpSel will tell ALU to perform AND. MemW is…

Q: Which of the following conditional transfer instructions? Select one: O a. JZ L O b. JMP L O c. CALL…

A: Given a set of microprocessor instructions, and we need to tell if they are conditional transfer…

Computer Fundamentals

The computer is termed computation. For calculating or computing something the device that has been used is known as the computer. Or we can say that for performing a fast arithmetic operation the device that has been used is a computer. Storing, processing, and retrieving are the main features of a computer.