5. Pipelined datapath has five stages, ie., instruction fetch (IF), decode (ID), execution (EX), memory(MEM), and write back (WB). It has a hazard detection unit. An instruction will be stalled at thedecode stage if any of its operands isn't ready. Consider executing the following code on this datapath(1) At the end of fifth cycle of execution, what instruction will be in each of the pipelinestages? (If there is any "bubble" in the pipeline, please write "NOP" in thecorresponding pipeline stage.) (5%)You must write the answer with the following format.instructionIFinstructionlw $r2, 10($1)sub $r4, $13, Sr2add $r5, Sr6, $7and Sr8, Sr4,$r5IFIDEX(2) If the datapath has a forwarding unit to resolve the data hazard, what instruction will be ineach of the pipeline stages at the end of the fifth cycle? (If there is any "bubble" in the-pipeline, please write "NOP" in the corresponding pipeline stage.) (5%)You must write the answer with the following format:(DMEMEXWB.MEMWR

Given InstructionsI1: lw $r2, 10($r1)I2: sub $r4, $r3, $r2I3: add $r5, $r6, $r7I4: and $r8, $r4,…

He stage if any of its operands isn't ready. Consider executing the followi lw $r2, 10($1) sub $r4, $r3, Sr2 add $r5, $r6, $7 and $r8, Sr4,$r5 At the end of fifth cycle of execution, what instruction will be in each of

He stage if any of its operands isn't ready. Consider executing the followi lw $r2, 10($1) sub $r4, $r3, Sr2 add $r5, $r6, $7 and $r8, Sr4,$r5 At the end of fifth cycle of execution, what instruction will be in each of

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

For sub $rd, $rs, $rtReg[rd] = Reg[rs] + Reg[rt] - Which resources (blocks) perform a useful function for the given instructions? - Use the following diagram for each instruction and trace its flow(use pen or highlighter) for the execution of that instruction. - List the units that are used for each instruction. (I mainly need help with tracing, please and thank you)
10.- Consider the following code and pictureLoop1MOVLW 0x32MOVWF REG2DECFSZ REG2,FGOTO LOOP1 If the system clock frequency is aMHz and each machine cycle consumes 4 cycles of it. Calculate the delay time of the LOOP1 loop. Include the execution difference time of the DECFSZ instruction in the last cycle. Select an answerA) 0.6.sB) 6msC)6usD) 60us
heeeelp
Question
Variable A contains the value 0x01. What will be the content of the Z status bit after execution of the following instruction? movf A, W Z = [?]
E In the following code block(Reference:Q11), you will a set of assembly instructions with corresponding line numbers (line numbers are for informational purpose only and they are not part of the source code). 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 mov edx, 5 dec ecx jmp LABEL1 mov eax, 1 LABEL1: mul edx jmp ecx mov edx, 0678h sub edx, eax jmp DWORD PTR [edx] neg ebx add ecx, ebx mov eax, 0 For each of the conditions/scenario listed below, indicate the corresponding line number (that cause or is associated with the condition/scenario). Enter 0 (Zero) if the condition is not caused by the block of code. 1) Memory indirect jump: type your answer... type your answer... type your answer... type your answer... 2) Register indirect jump: 3) Relative short jump: type your answer... 5) Two's complement type your answer... 4) Relative near jump: 6) Unreachable code
According to the code given below, what is the value stored in the offset field of the "bne $t1, $a3, L1" instruction? L1: L2: L3: 06 0-7 07 S -8 8 sll sll add add add Iw add add Iw 28 32 add addi bne addi bne add add bne addi $a2, $a2, 2 $a3, $a3, 2 $v0, Szero, Szero $t0, $zero, Szero $14, $a0,$t0 $t4, 0($t4) $t1, $zero, Szero $t3, $a1, $t1 $13, 0($13) St3, $a1, $t1 $t1,$t1, 4 $t1, $a3, L1 Sto, Sto, 4 $t1, $a3, L2 $t1, $zero, Szero $13, $a1, $t1 $t1, $a3, L3 Sto, $to, 4