12 m3 of liquid at 30° C and 125 kPa is permitted to expand isothermally to 30 m3, determine the bulk modulus of elasticity of the liquid and the coefficient of compressibility of the liquid.

Q: Plate with 0.13 m wide and 0.25 m length passes thru oil with layer 3.5 mm and 5 mm thick. Both…

A:

Q: A copper alloy wire of 1.9mm diameter and 30m long hangs freely from Tower. What will be its…

A: Step 1

Q: A liquid with dynamic viscosity of 0,00275 kg/m.s and specific weight 9 KN/m' fills the space…

A:

Q: Water is placed in a hydraulic press initially at 140kPa absolute, the pressure is increased to…

A: Given,  Bulk modulus (k)= 2.5GPa = 2.5×10⁹ Pa bulk modulus(k)= Increase of pressure / Volumetric…

Q: RN, and a force, F= 66 KN) inclined at an angle alpha = 30 degrees from the vertical, such that it…

A:

Q: 8. True or False Solids are more difficult to compress than gases or liquids because of the rigid…

A: Liquids have no definite shape but fixed volume, so they can change the shape and can be compressed…

Q: The extruded plastic shape has dimensions of D = 36 mm, d = 32 mm, a = 83 mm, and t = 6 mm.  (a)…

A: The neutral axis of the given geometry…

Q: A cylindrical tank holding oxygen at 1,146 kPa pressure has an outside diameter of 430 mm and a wall…

A:

Q: A circular nylon [E = 8 GPa; v=0.35; a=20x106/°C] disk with a circular hole in its center is shown.…

A:

Q: 5Q. The plate is moving at 0.6 mm/s when the force applied to the plate is 4 mN. If the surface area…

A:

Q: THIN WALLED PRESSURE VESSELS SITUATION: A cylindrical water tank is 8 m in diameter and 12 m long.…

A: Given:- Diameter of cylinder = 8 m Length of cylinder = 12 m Material stress = 40 MPa

Q: * Fixed-Fixed bar was 20 centigrade degree at room temperature, Determine the thermal stress when…

A:

Q: 1. The cylindrical tank has an outer radius of 2 m and a wall thickness of 35 mm. If the tank is…

A: given data: Pressure(P)=1.75 MPa Radius (R)=2 m thickness (t)=35 mm

Q: The strength per meter of the longitudinal joint of a cylindrical tank is 475 kN, whereas the girth…

A:

Q: What is the working strength of a 2" bolt which is screwed up tightly in a packed joint when the…

A: As per guidelines we need to answer only first question so please repost rest questions separately

Q: A 10 il load is uniformly cated by an aluminum alloy pipe with an outside diameter of 10 cm and…

A:

Q: A pressure of 65 MPa at a specific depth in the ocean and the average bulk modulus of elasticity is…

A:

Q: For question 103A and 103B, the thin-walled cylindrical container shown below. Say p is the internal…

A: Given data:Internal pressure, p=15 MPa or 15 N/mm2Inside diameter, d=20 mmWall thickness, t=10…

Q: In figure, if the fluid is SAE 30 oil at 20 °C (= 0.44 Pa.s) and D=7mm, what shear stress is…

A:

Q: A rectangular nylon [E =8 GPa; v=0.35; a= 23x10 6/°C] plate has a circular hole in its center. At an…

A:

Q: As shown, a gas storage tank is composed of half cylindrical thin shells (8m long) and hemispherical…

A: first calculate the the  hoop stress of the cylinder portion of tank σ=prtc140=3×2tctc=370=0.04m now…

Q: A 0.35-m long steel rod with a round cross-section (25 mm) is resting on a frictionless surface. The…

A: The given data is: Length of steel rod (L) = 0.35 m Diameter of steel rod (d) = 25 mm Coefficient of…

Q: steel pressure vessel (_y = 250 MPa, E = 200 GPa) has a length of 4 m and  a diameter of 1.2 m…

A:

Q: If the stress at proportional limit of the material is 248 MPa, which of the following gives the…

A: Given Data: The column is fixed at both ends and braced at mid-height about the weak axis. The…

Q: A submersible cylinder used in research has a cylindrical pressure hull of outside diameter 3.0 m…

A: First we summarise the given data : Outside diameter = 3.0 m Wall thickness = 150 mm Yield point =…

Q: A steel cylindrical pressure vessel at an industrial plant has a diameter of D = mm. The cylinder…

A:

Q: Plate with 0.13m wide and 0.25 m length passes thru oil ewith layer 3.5mm and 5mm thick. Both…

A:

Q: Particle A lies on the x-y plane and is acted on by the three forces shown. Find the resultant of…

A: Istead of points A, B, C, D TAKEN E, F, G, H

Q: An axial load of 900 KN is carried by a compound tube comprising of a steel tube and a brass tube.…

A:

Q: A flat annular steel disc of 0.8 m outside diameter and 0.15 m inner diameter is to be shrunk around…

A: Pressure is defined as the force that crosses a “small” boundary in each unit area of ​​that…

Q: A cast-iron cannonball is found by a diver on the bottom of a harbor (SG of harbor water = 1.02) .…

A: To lift the ball, there will be three force which will act on the ball. Weight Buoyancy  And drag…

Q: Q3. An aluminium-alloy cylinder of internal diameter 10.000cm and wall thickness 0.50cm is shrunk…

A:

Q: Specific Gravity of the liquid AC and DB is 0.80 and Specific Gravity of CD is 1.XY. If the pressure…

A:

Q: A hollow steel rod has a length of 1m. The outside diameter of the rod is 0.2m and the inner…

A: Given: Length of rod, L = 1 m = 1000 mm Outside diameter of rod, Do = 0.2 m = 200 mm Inner diameter…

Q: A steel penstock 60 cm in diameter has a shell thickness of 1.2 cm. The modulus of elasticity of…

A:

Q: A cube contracts in volume by 0.05% when acted upon by normal uniform pressure of 2x 106 N/m? on all…

A: Given data: The value of uniform pressure ∆P=2×106 N/m2 The value volumetric strain…

Dependence on mechanical properties

The mechanical properties of materials are those structures that include the reaction to the load used. Metal switching features determine the scope of the usefulness of the content and establish the expected service life. Machine structures are also used to help distinguish and identify material objects. The most common mechanical properties considered are strength, ductility, stiffness, impact resistance, and resilience to fractures.