A steel cylindrical pressure vessel at an industrial plant has a diameter of D = <1.40+last three digit of roll/1000) m and wall thickness of t = <20.0+last digit of your roll> mm. The cylinder body has length L= 6.00 m. For steel, E = 200 GPa, Yield Strength = 480 MPa, and Poisson's ratio v = 0.30. (a) Using a factor of safety against yielding of 3.0, determine the allowable (maximum working) pressure of the contained gas. (b) If the contained pressure is 600 kPa, determine the change in length of the cylinder from its unpressurized (unloaded) state. (c) If the contained pressure is 600 kPa, determine the change in radius of the cylinder from its unpressurized (unloaded) state.

A steel cylindrical pressure vessel at an industrial plant has a diameter of D = <1.40+last three digit of roll/1000) m and wall thickness of t = <20.0+last digit of your roll> mm. The cylinder body has length L= 6.00 m. For steel, E = 200 GPa, Yield Strength = 480 MPa, and Poisson's ratio v = 0.30. (a) Using a factor of safety against yielding of 3.0, determine the allowable (maximum working) pressure of the contained gas. (b) If the contained pressure is 600 kPa, determine the change in length of the cylinder from its unpressurized (unloaded) state. (c) If the contained pressure is 600 kPa, determine the change in radius of the cylinder from its unpressurized (unloaded) state.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine which commands can be used for this drawing. (AUTOCAD COMPLETE VERSION) Select all that applies ●CIRCLE ●ARRAYPOLAR ●LINE ●SHIFT TANGENT + RIGHT CLICK (FOR TANGENT LINES) ●FILLET ●GCHORIZONTAL ●CENTER MARK ●SPLINE ●DIMENSION ●ARRAYRECT ●MIRROR ●DCON ● GCTANGENT ●GCONCENTRIC
How to solve this?
4. Complete the accompanying set of profile notes and perform the arithmetic check. Provide a sketch of this project's profile view. (You can use excel to sketch) Station BS (ft) HI (ft) IS (ft) FS (ft) BM1 0+00 1+00 2+00 3+00 3+35 4+00 TP1 5+00 5+20 5+30 6+00 BM2 4.58 4.87 2.59 3.79 4.82 4.98 5.05 7.30 4.60 4.78 4.85 4.89 11.21 10.58 Elevation (ft) 427.06
Compute the setting out coordinates. Angle A is 20 degree 3 minute 16 second
Define HDOP and VDOP?
they are the only ines i need please help me. it is confusing me.
Compute the area of the traverse data shown.
Fill in the blank question: Q. GIS is known as ___________ System.
What is the elevation at point A, C, and E?
Y 20⁰ 30° 30° 500N 'x' X
The givin is in the 2nd photo
Given the table below, compute the area of the traverse by coordinates method. Traverse x-coor 0.00 25.00 45.00 ABCDEFGH A Area 75.00 y-coor 0.00 3.00 27.00 8.00 -28.00 -50.00 -25.00 -5.00 0.00 35.00 39.00 10.00 15.00 0.00 [a] square units * Express all values up to 3 decimal places. Do not include the unit in writing the answer/s.