The following is the bearing and length measurements of an opentraverse A) Determine the latitude and departure of the lines B) What is the distance from the starting point of A to the last point of F Line length 100m BEARING N 30deg30'E N45 degE S 60 degE S 85 deg W N 40 degE line AB BC 200m CD 250m DE 75m EF 140m

The following is the bearing and length measurements of an opentraverse A) Determine the latitude and departure of the lines B) What is the distance from the starting point of A to the last point of F Line length 100m BEARING N 30deg30'E N45 degE S 60 degE S 85 deg W N 40 degE line AB BC 200m CD 250m DE 75m EF 140m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Assume contour interval of 5 m, draw the contour lines based on the given elevations of the points of the figure below. Make sure to draw in heavy lines the index contours and indicate the contour label in them, and intermediate contours in regular lines. (Note: you may just estimate the location of contour points (or visual interpolation), no need to do interpolation calculations)
Quiz1 Your email address will be recorded when you submit this form. Not maram.kadhim.moren1558@student.uobabylon.e du.iq? Switch account Two rods are attached at A to lever AB. Using the parallelogram law and knowing that the force in the left-hand rod is F1 = 120 N, F1. F2 28° 10° OB
In 1860 the magnetic bearing of a line was N 69 deg 27 min W with a magnetic declination of 5 deg 12 min E. What is the magnetic bearing of this line today if the magnetic declination is now 7 deg 36 min E? O a. S 71 deg 51 min E b. S 17 deg 51 min E c. N 71 deg 51 min W O d. N 17 deg 51 min W
Draw the free-body diagram for the figure shown, then determine the tension forces in cables BA and BC to hold a 450 N. 30° 450N Attach File Browse Local Files Browse Content Collection board/content/listContent.jsp?course_id= 226938 1&content_id= 7568158_1&mode=reset -3°C Cloudy ^ 40) DELL F12 PrtScr Insert Delete 近

Can you please give me the plot of this Profile notes. Please do not give me the solution I am done with it already. I just need help on the plotting to check if I am doing the right thing. Thank you
Which feature control frame would you use to tolerance the one-inch slot perpendicular to datum feature A and symmetrical with the four-inch feature within a tolerance of .005 at MMC in the drawing below? Use MMC and MMB wherever possible. 1.000-1.010 138 4.000-4.020 A. B. C. D. E. O E O O A с B B OD .005(M) A 4.00 .005 MA BM 1 005 (M) A BM 0.005MABM .005 M AMB 2.00 A
The answer is indicated in the image
METERS | FEET MODEL: IA6BJM SIZE: 8" x 6" x 13" RPM: 1750 76+250 PRESSURE MAX: 120 PSI GRAPHIC 61+200 Ø13," (75 HP) SCALE. 70% 75% 80% 82% 83% 60 GPM Ø12" (60 HP) 84% 83% 82% 80% 46+150 Ø12%" (50 HP) 75% 011%" (40 HP) 70% 65% 31+100 100 BHP Ø10%" (30 HP) NPSHr ft m 75 BHP 60 BHP 30+9 15+50 50 BHP 30 ВНР 40 BHP 20+6 NPSHr 10+3 GALLONS PER MINUTE LITERS PER MINUTE Refer to the system curve drawn on this pump curve. If two pumps are used in series (11 7/16" impellers), what is the expected efficiency (%) for each pump? 1136+300 2271+600H 006 20 4543+1200아 5678+1500 6414+1800 7949+2100아 9085+2400 11356+3000 10 FEET
Use Factor method in solving this problem. Details are already provided in the drawing
Determine the coordinates of the centroid of the shaded area. y 15 E 25 30 15 40 50 I 30 – x 95 Dimensions in millimeters Answers: i mm i mm II
Q2. Find Iep -30 50 В 20 A 40 R=20 +-20 - y 20 40 Ix
a distance measured with a 50m steel tape is recorded as 685.24m the tape is known to 0.014 too long what is the correct length of the line i n meter