A rectangular nylon [E =8 GPa; v=0.35; a= 23x10 6/°C] plate has a circular hole in its center. At an initial temperature of T₁ = 22°C, the plate widthis b=310 mm, the plate height is h = 220 mm, the diameter of the central holeis d = 60 mm, and the thickness of the plateist= 18 mm. At a final temperature of Tf=59°C, determine (a) the diameter d of the central hole. (b) the thickness t of the plate. Answers: (a) df = i (b) t= i b d mm mm

A rectangular nylon [E =8 GPa; v=0.35; a= 23x10 6/°C] plate has a circular hole in its center. At an initial temperature of T₁ = 22°C, the plate widthis b=310 mm, the plate height is h = 220 mm, the diameter of the central holeis d = 60 mm, and the thickness of the plateist= 18 mm. At a final temperature of Tf=59°C, determine (a) the diameter d of the central hole. (b) the thickness t of the plate. Answers: (a) df = i (b) t= i b d mm mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

H.W.6: A hollow circular cold-rolled bronze [G, = 6,500 ksi] tube (1) with an outside diameter of 1.75 in. and an inside diam- eter of 1.25 in. is securely bonded to a solid 1.25-in.-diameter cold-rolled stainless steel [G2 = 12,500 ksi] core (2) as shown in Figure and the allowable shear stress of core (2) is 60 ksi. Determine . The allowable shear stress of tube (1) is 27 ksi, (a) the allowable torque T that can be applied to the tube-and- core assembly. (b) the corresponding torques produced in tube (1) and core (2). (c) the angle of twist produced in a 10-in. length of the assembly by the allowable torque T. (1) т. FIGURE
i need the answer quickly
A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-6/°C; v = 0.33] pipe has an outside diameter of 210 mm, a wall thickness of 11 mm, and a length of 5.8 m. The pipe supports a compressive load of 675 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) d = i mm AD= i mm
1.A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are € E =0.40x10-3 and ɛ =0.3 x 10- determine O and o. Use E = 110 GPa and v=0.35. y y. = Blank 1 MPa Answer in 1 decimal place = Blank 2 MPa Answer in 1 decimal place
A steel bar is heated from room temperature to 80oC while it is free to expand. The bar will therefore be subject to: A. compression B. tension C. no stress D. shear
ASAPPP THANKS
d) Find the stress (in psi) induced in the aluminum tube by the temperature change.
A polymer cylinder (2) is clamped between rigid heads by two steel bolts (1). The steel [E = 29,000 ksi; a = 6.5×10-6/°F] bolts have a diameter of 0.50 in. The polymer [E = 380 ksi; a = 39.7x 10-6/°F] cylinder has an outside diameter of 7.0 in. and a wall thickness of 0.40 in. Assume a = 22 in. and b = 30 in. If the %3D temperature of this assembly changes by AT = 125°F, determine: (a) the normal stress in the polymer cylinder. (b) the normal strain in the polymer cylinder. (c) the normal strain in the steel bolts. |(1) (2) C а (1) b. Answer:
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of 170 mm, a wall thickness of 12 mm, and a length of 4.5 m. The pipe supports a compressive load of 630 kN. After the temperature of the pipe drops 53°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) d = i AD= i mm mm
The masses of the blocks are ma = 30 kg and mg = 70 kg. Between all of the contacting surfaces, u=0.2. What is the largest force F that can be applied without causing the blocks to slip?
SHOW COMPLETE SOLUTION AND DRAW ILLUSTRATION
A circular nylon [E = 8 GPa; ν = 0.35; α = 29 ×10-6/°C] disk with a circular hole in its center is shown. At an initial temperature of Ti = 22°C, the outer diameter of the disk is D = 210 mm, the diameter of the central hole is d = 55 mm, and the thickness of the disk is t = 24 mm. At a final temperature of Tf = 46°C, determine:(a) the change in diameter Δd of the central hole (assume an increase Δd as positive, otherwise as negative).(b) the change in thickness Δt of the disk (assume an increase Δt as positive, otherwise as negative).(c) the normal strain in the circumferential direction around the outside of the disk.