3. A steel bolt through a 30-in long aluminum tube has the nut turned on until it just touches the end of the tube. No stress is introduced on the bolt or the tube. The temperature of the assembly is raised from 70 to 81 degrees Fahrenheit. The cross-sectional area of the bolt is 0.09 sq. inch and the cross-sectional area of the tube of 0.30 sq. inch.

3. A steel bolt through a 30-in long aluminum tube has the nut turned on until it just touches the end of the tube. No stress is introduced on the bolt or the tube. The temperature of the assembly is raised from 70 to 81 degrees Fahrenheit. The cross-sectional area of the bolt is 0.09 sq. inch and the cross-sectional area of the tube of 0.30 sq. inch.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

22. two decimal places
A scuba tank is being designed for an internal pressure of 2,650 psi with a factor of safety of 2.0 with respect to yielding. The yield stress of the steel is 69,000 psi in tension and 20,000 psi in shear. (Assume that the given radius or diameter is an inside dimension and that all internal pressures are gage pressures.) (a) If the diameter of the tank is 7.0 in., what is the minimum required wall thickness (in inches)? inches (b) If the wall thickness is 0.25 in., what is the maximum acceptable internal pressure (in psi)? psi
1) The head H is connected to the cylinder of a compressor using six steel bolts. If the clamping force in each bolt is 4000N, determine the normal strain in the bolts. Each bolt has a diameter of 5 mm. If o₂ = 280 MPa and Est = 210GPa, what is the strain in each bolt when the nut is unscrewed so that the clamping force is released? a) 0.970 b) 0.203 c) 0.970(10-³) d) Insufficient information to determine because the stress is beyond yield point H &
Determine the compressive force (in lb) in the bars shown after a temperature rise of 173°F if d = 0.015 in. Round off the final answer to five decimal places. Use the following data: Bronze Aluminum A = 2.24 sq. in A = 2.78 sq. in E = 14959726 psi E = 10594540 psi L = 12.5 in L = 16.6 in α = 11.61 x 10-6/ °F α = 12.67 x 10-6/°F
What is the maximum concentrated load that can be applied at the end of an embedded hollow pipe, made of AISI 1020 steel? Take 10.16 cm for the outside diameter, and 6.35 cm for the inside diameter. The length of the pipe is 183 cm. Its maximum deflection must not exceed 5.08 cm. Neglect the weight of the pipe. Answer 22816 N
For the figure shown, determine the stresses of the wires and the elongation when the temperature change is 45°. Aluminum Steel Area 800 mm? 600 mm? E 70GPA 200GPA Coefficient of Linear 23 micro m/mC 11.7 micro m/m°C Expansion stel AL 3M zm 20 kuym
A steel rod of length 300 mm and diameter 30 mm, is subjected to a pull 'P' while the temperáture Is 100°C. If the total extension of the rod is 0.40 mm, calculate the magnitude of 'P'. Take 'a' for steel 12 x 10 °C and E = 0.215 x 1012 N/m2. %3D
PROBLEM 01: Hollow bar length is 1.40m long and tube length is three-fourth as long as the bar. Torque T=1100N.m acts at the free end of the bar. Both the bar and tube are made of an aluminum alloy with shear modulus of w ww elasticity G=27GN/m². Given that dl=35mm, d2=45mm, d3=60mm, d4=70mm. Determine the following: a. Maximum shear stress in both the bar and tube b. Angle of twist at the end A of the bar. (In degrees) Tube Fixed plate End plate Tube d3 d1 d2 d4 Bar Cross-section of the bar and tube
The assembly shown in Figure No. 3 consists of a hollow steel [E = 200 GPa] tube (1) with an outside diameter of 60 mm and a wall thickness of 5 mm, a solid 40 mm diameter aluminum [E= 70 GPa rod (2), and a solid 30 mm diameter aluminum rod (3). The member lengths are L1 2 000 mm, L2 = 1 200 mm, and L3 %D 3D800 mm. The following loads act on the assembly: P = 150 kN, Q = 80 kN, and R = 115 kN. Determine (a) the change in length of steel tube (1). (b) the deflection of joint D with respect to the fixed support at A.
Please help I need it in 30 minutes
2. two decimal places
Please show a detailed solution and explanation including its FBD. Thank you!