20 mm 10 mm 10 mm 20 mm 10 mm 10 mm The Aluminum machine part is subjected to a bending moment M = 75 N.m. Determine (a) distance of neutral axis from the bottom of the cross section, (b) moment of inertia of the cross section about the neutral axis, (c) maximum stress at point B, and (d) maximum stress at point C. 10 mm M-75 N-m 40 mm

20 mm 10 mm 10 mm 20 mm 10 mm 10 mm The Aluminum machine part is subjected to a bending moment M = 75 N.m. Determine (a) distance of neutral axis from the bottom of the cross section, (b) moment of inertia of the cross section about the neutral axis, (c) maximum stress at point B, and (d) maximum stress at point C. 10 mm M-75 N-m 40 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A Sandwich block is comprised of brass in the centre with two aluminium plates attached to either…

Q: The aluminum machine part is subjected to a moment of 75 kNxm. Determine the bending stress created…

A: Solution:Given: The moment acting on the section is M=75N.m which is sagging, so the topmost fiber…

Q: Determine the maximum load P that can be applied in the system consisting of a bent bar bolted at…

Q: The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum…

A: The given data is shown below: Diameter of aluminium rod=19mmElastic modulus=69 GPaDiameter of steel…

Q: An axial force of 100 kN is applied to the assembly shown by means of rigid end plates. Determine…

A: Given: The axial force is 100 kN. The modulus of elasticity for the brass core is 105 GPa. The…

Q: Consider two shafts one solid of mild steel of 200 mm diameter and another hollow of alloy steel of…

A: The diameter of the solid shaft is 200 millimeters.The outer diameter of the hollow shaft is 200…

Q: The assembly consists of two red brass C83400 copper rods AB and CD having a diameter of 30 mm, a…

A: Figure is as shown

Q: A threaded round steel bar is subjected to a tota axial pull of 8000 lb. If the diameter of the…

A: Take diameter of threaded portion≈unthreaded portionso,Stress=PArea

Q: Q4 A beam made of the cross section shown below is made of an elastic- plastic material for which…

A: yield stress - 360 MPa To find- (a) Find the plastic moment Mp(b) The maximum elastic moment…

Q: Taking into account only the effect of normal stresses, determine the strain energy of the prismatic…

Q: Consider two shafts one solid of mild steel of 200 mm diameter and another hollow of alloy steel of…

A: The diameter of the solid shaft is 200 millimeters.The outer diameter of the hollow shaft is 200…

Q: 2. A steel rod of 20 mm diameter passes centrally through a copper tube 40 mm external diameter and…

A: Given data: Ds=20 mm External Dc=40 mm Internal Dc=30 mm T= 60∘C Es=200×109 N/mm2Ec=100×109…

Q: The temperature of the cylindrical rod is heated to 45°C which is fixed in between A and C rigid…

Q: *11-80. The man has a mass of 78 kg and stands motionless at the end of the diving board. If the…

A: Given : Mass =…

Q: A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the…

Q: Part A shown construct an equilibrium equation that relates the axial load in the steel and…

A: Uniform distributed load, Length of all post, Diameter of steel post, Diameter of aluminum post, To…

Question

20 mm
10 mm
10 mm
20 mm
10 mm
10 mm
The Aluminum machine part is subjected to a
bending moment M = 75 N.m. Determine (a)
distance of neutral axis from the bottom of the
cross section, (b) moment of inertia of the cross
section about the neutral axis, (c) maximum stress
at point B, and (d) maximum stress at point C.
10 mm
M-75 N-m
40 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question 4. Three wires are used to suspend the plate shown. Aluminium wires are used at A and B with a diameter of 3 mm and a steel wire is used at C with a diameter of 2 mm. Knowing that the allowable stress for aluminium (E = 72 GPa) is 96 MPa and that the allowable stress for steel (E = 200 GPa) is 124 MPa, determine the maximum load P that may be applied. L L P B
Q2 - The assembly shown below consists of three rods AB, CD and EF with the following properties: AB and CD: Modulus of elasticity = 75 GPa; Diameter = 30 mm EF: Modulus of elasticity = 200 GPa; Diameter = 15 mm If there is a 0.5 mm gap at A and C before loading, Determine the average normal stress developed in rods AB, CD and EF. Note: The cap GH is rigid. 0.5 mm -250 mm A C 30 mm 30 mm B D H G E 500 mm 50 kN 50 kN 15 mm F
Solve it
Please show intermediate steps including free body diagrams, equations used, and problem setup so that your approach can be followed.
11-59. The aluminum machine part is subjected to a moment of M-75 kN-m. Determine the maximum tensile and compressive bending stresses in the part. 10 mm 10 mm, 10 mm 40 mm B 20 mm 10 mm 10 mm M-75 N·m
4) 4 points Calculate the minimum net area for the plate shown below connected to 14 mm thick gusset plate with 22 mm bolts. Plate 12 mm thick 35mm 20mm 20mm 150 mm 20mm 20mm 35mm „Gusset 14 mm thick 35mm 30mm 30mm 40mm a. 936 mm? b. 918 mm? c. 900 mm? d. 887 mm?
#2 will upvote to anyone who will answer
6:53 PM M ..39 and 300 mm long solid copper bar of 20 mm diameter (See Figure 1). The composite bar is heated 35°C above room temperature, clamped at both ends and then allowed to cool to room temperature. If the distance between the clamps is unchanged find the stress in each bar. For steel, use a = 12.5 x 100% E = 200 GPa and for Aluminum use a = 17 x × 10**; E = 130 GPa 500 m Figure Q1 Question 2 A narrow steel strip, 15 mm thick, is clad by two magnesium plates, one is 2.5 mm thick and the other is 3.5 mm thick as show in Figure 2. Calculate the change in stress in each strip for a centigrade degree rise in temperature of the compound strip. Assume perfect bonding of the strips along their length. For steel, a = 12 x 10°/°C; E = 200 GN/m². For magnesium, a = 27 x 10°/°C; E = 45 GN/m² 3.5mm 15 mm 2.5 mm Figure Q2 Question 3 A horizontal beam AD, 10 m long, carries a uniformly distributed load of 25kN/m, together with a concentrated load of 36 kN at the left-hand end A (see Figure…
A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1350 µm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. A 240 mm B (1) O 1281 um/m O 1877 µm/m O 1141 µm/m O 1358 µm/m O 999 µm/m 360 mm (2) Rigid bar 900 mm C 140 mm, 1,500 mm
Problem 1 An axial force of P is applied to the center of the rigid end plate shown below. If the portion of the load carried by the aluminum plates is half the portion of the load carried by the brass core, (a) determine the value of h, (b) the total load if the stress in the brass is 50 MPa. Brass core (E = 105 GPa) Aluminum plates (E = 70 GPa) Rigid end plate 300 mm 60 mim 40 mm
The column above is subjected to axial loading only. Assume the following: • E= 29000 ksi G = 10000 ksi • = 986 in4 A = 60 in? • L= 20 ft • Grade 60 steel (60 ksi yield stress) • The column is fixed at the top and pinned at the bottom Which of the following is closest to the maximum normal stress the column can support (before yielding or buckling)? 167 ksi 24 ksi 42 ksi 60 ksi
The solid rod has a diameter of 20mm. Find the following: Angle of twist at C with respect to A (in radians) Angle of twist at B with respect to A (in radians) Maximum shear stress at A (in MPa) (Shear stress at support, at a point 7mm from center. (in MPa) A-36 steel with the following properties: Modulus of Elasticity, E = 29x10^3 ksi or 200 GPa Shear Modulus/Modulus of Rigidity, G = 11.5x10^3 ksi or 79.3 GPa Poisson's Ratio, nu = 0.260 Temperature Coefficient for thermal expansion, a = 6.6x10^-6/°F or 11.7x10^-6/°C