A copper cylinder 150mm outside diameter has walls 25mm thick. End plates are stayed by a 25mm diameter bar of steel which passes through the cylinder and is just tight at -11°C. Estimate the stress in cylinder and stay when steam at atmospheric atmosphere (100°C) is admitted. Assume the end plates do not deform. Use the following values: ac = 17 x 10-6/°C Ec = 117 GPa a, = 12 x 106/°C Es = 200 GPa

Q: Which of the following shapes are generally considered when the area is ?computed by map…

A:

Q: put dimensions on the drawing using the details

A: 3@50, 5@100, 7@150, and rest at 200mm center to center is spacing of ties in column. This detail…

Q: What is the overall density? %

A: This question is related to the Soil Mechanics from Civil Engineering.

Q: 5.1 The recommended scales for use on technical drawings are specified in the following table.…

A: To find: Choose the suitable code for the given scales for use on technical drawings.

Q: Compare and contrast the uses of T-square and setsquares.

A: T-square: It is a technical instrument that is used for drawing purposes.  It is mainly used by…

Q: Add/Subtract the following DMS measurements by hand. In your answer, separate each unit by a comma…

A:

Q: How many "varas" are there in a single ruler measurement?

A: A single ruler is the standard ruler which has measurements given in inches or mm. It is used to…

Q: A triangle has an area of 14 sq ft and a base of 7 feet. What is the height of thetriangle?

A: given data :  area of triangle (A) = 14 square feet  base (b) = 7 feet  height (h) = ?

Q: 32. What is the area of an octagon inscribed in a circle having an area of 224 sq.m?

A:

Q: how did you get 1.5 for the first part

A: In the original question it is stated that Vmax=2 Vmin In the solution, the following is given.…

Q: The shape factor for the uniform section shown below is 20 Î 20 + 50 50 * 50 50

A:

Q: Convert 24 inches to feet.

A:

Q: A 2in x 2in x 1/4in angle bar with a length of 24 inches has width-thickness ratio of

A:

Q: Only Draw profile with appropriate scale

A: To draw the profile to the given levelling

Q: ETERMINE THE LOCATION OF CENTROIDAL X AND Y. NOTE: UNITS ARE IN INCHES.

A:

Q: express each measurement in feet.42 inches

A: Given: The measurement is 42 in.

Q: what is the difference between 42 square meter and 42 meter square

A: It is needed to differenciate between 42 square meter and 42 meter square.

Q: R10 30 50 O. 15 R30

A:

Q: Which of the following shapes are generally considered when the area is ?computed by map…

A: Given: shape of map To determine:  Which shape generally considered  for area calculation.

Q: Convert 6.2 feet to inches.

A: Given: The measurement is 6.2 ft.

Q: H MM 0 10 20 30 40 50 60 70 80 90 100 DIMENSION THE PART USING METRIC DIMENSIONS. USE DIVIDERS OR…

A: The front view and top view of an object is shown in the above figures. Also scale of dimensions…

Q: How

A: 1 and 1 actually is the ratio representation of slope.

Q: express each measurement in feet.50 inches

A: Given: The measurement is 50 in.

Q: me miller indices.

A: Given figure

Q: Express all denominate numbers 8 gal 3 qt  35 qtin the same unit.

A: Solution:-

Q: The coordinates of centroid for the following section is 150 mm - 20 mm 20 mm 20 mm 300 mm 500 mm

A:

Q: Part A What is the ratio scale for the equivalent scale of 1 in. = 80 ft? Express your answer using…

A: 1 ft =12 inch given 80 ft =12*80=960in Ratio scale=112×80=1:960

Q: Define sedimentary rocks.

A: Sedimentary rock, rock formed at or near the surface of the earth by sediment lithification and…

Q: Define matrix's diagonal, off-diagonal, subdiagonal, and superdiagonal elements. Illustrate each.

A: An n×n matrix, or a matrix with the same number of columns as rows, is known as a square matrix.

Q: 30 10 30 10 15 20 15 10

A: Line command of autocad is used  We can use either absolute coordinate method or relative coordinate…

Q: Define Relative Density.

A: Relative density or specific gravity:

Q: express each measurement in feet.108 inches

A:

Q: 112 тm К30 тm ->- 30 тm -+30 тm ->-30 mт -> Рart a) Determine the moment of inertia of the shaded…

A:

Q: Draw the figure to an enlarged scale in Isohyetal method

A: The iisohyetal approach is a technique for calculating the average amount of precipitation within a…

Q: sanitary engineering  solve by hardy Cross method  k=8*f*L/pi*g*D^5 f=0.02 g=9.81 pi=e.14

A: Given data in question  Length of pipe  Diameter of pipe Constant value of f Acceleration due to…

Q: express each measurement in inches.41⁄2 feet

A: GIVEN :- Measurement = 412 feet To Determine :- Convert the given measurement into inches.

Q: Below in Figure is an isometric drawing of a component. Draw in First Angle Projection the…

A: Question being asked here to draw the first angle projection in which the drawing pattern is…

Q: In the figure below, find the SAB 0 ,CAB OCF %D

A: Given data E=200000MPa P=36kN

Q: 3. £ 65 s² + 25 + 3 s² + 25

A:

Q: Where do I get Ix from?

A: Bending stress formula:or, M/ = Z  {here, Z = I/y}or, Z= = 1.376 x 106 mm3W 18 x 50 has Z = 1.557 x…

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.