steel pressure vessel (_y = 250 MPa, E = 200 GPa) has a length of 4 m and  a diameter of 1.2 m (cylindrical). It is  designed to hold natural gas at a pressure of 6 MPa.   Calculate the  wall thickness required to safely contain flammable gases, taking into account a safety factor of 5.0 to prevent failure. Use the "maximum principal stress" criterion.  Next, calculate the Von Mises stress corresponding to the stress state of  the reservoir.   Enter your numerical answer. Please include free body diagrams and possible steps

Q: For question 103A and 103B, the thin-walled cylindrical container shown below. Say p is the internal…

A:

Q: Question 11 of 12 - / 1 Current Attempt in Progress A 33 mm by 33 mm square ABCD (i.e., a = 33 mm)…

A: In this problem, we are given a square that is deformed into a rhombus due to the application of a…

Q: 1. A solid circular rod, 750 mm long and 30 mm diameter, is subjected to an axial force of 80 kN.…

A: Length (l) = 750mm dia (d) = 30mm Force (P) = 80kN Compression (∂l)= 1.35mm Change in diameter (∂d)…

Q: A cylindrical boiler with an outside diameter of 3.60 m and a wall thickness of 40 mm is made of a…

A:

Q: IS Smm. alculate the allowable internal pressure if the stress is limited to 40MP..

A: d=5m t=8mm

Q: Determine the hoop stress developed in a thin wall cylindrical pressure vessel of diameter 1.5 m and…

A: Given data : Diameter (d)=1.5 mwall thickness (t)=20 mmInternal pressure (p)=500 kPa

Q: Problem 2: Determine Maximum Normal stress. Golb 90b 20lb

A:

Q: Q3/ Steel tube shaft having length 4mm change in temperature ( 102 °c drop). Where, E-210*10³ MPa ,a…

A: Given that,  length of steel tube, L = 4mm change in temperature, ∆T=-102°C (drop) modulus of…

Q: a. Celerity of the pressure wave b. Equivalent bulk modulus of water c. Pressure on the pipe after…

A:

Q: J.20 (C). A thick cylinder of 100 mm internal diameter and 125 mm external diameter is wound with…

A: step 1-

Q: Problem 1. In a test on an aerosol can it was loaded to a gage pressure p = 69.0 psi. While…

A: inside pressure p=69 psinormal load N=400 lb and torque  T=250 lb-indiameter d=3.0 in   and radiud…

Q: A spherical balloon is filled with a gas. The outer diameter of the balloon is 12 in, and the…

A:

Q: A tank in the shape of sphere is filled with fluid and then pressurized. The diameter of the tank is…

A:

Q: A cylindrical tank holding oxygen at 1,146 kPa pressure has an outside diameter of 430 mm and a wall…

A:

Q: (1) A cylindrical tank is required to contain a gage pressure 630 kPa. The tank is to be made of A5…

A: as per guidelines we need to answer only 1st question

Q: THIN WALLED PRESSURE VESSELS SITUATION: A cylindrical water tank is 8 m in diameter and 12 m long.…

A: Given:- Diameter of cylinder = 8 m Length of cylinder = 12 m Material stress = 40 MPa

Q: Answer

A:

Q: When filled to capacity, the unpressurized storage tank shown contains water to a height of h= 20…

A: Given t = 0.625 inch H = 20 ft Diameter = 8 ft

Q: A cylindrical tank of oil (sg 0.8) is 8m in diameter and 15mm thick. If the tank is to be completely…

A: D=8m t=15mm

Q: a compound cylinder is to be made by shrinking one tube on to another so that the radial compressive…

A: Given : radial compressive stress at the junction = 28.5N/mm2 outside diameter = 26.5cm bore…

Q: Differentiation of the laminar pipe flow solution shows that the fluid shear stress τ(r) varies…

A: The expression for the velocity profile for the steady, laminar and incompressible flow of flow of…

Q: Question Wall thickness of a thin cylinder shell of 800 mm internal diameter is 10 mm. length of the…

A: A thin cylinder shell-Internal diameter d=800 mm,Wall thickness t=10 mm,Length of cylinder l = 2…

Q: Calculate the wall thickness required for a thin-walled cylinder which must withstand a pressure…

A: Given data  Pressure difference (P) = 1.5 MPa  Mean diameter (d) = 200 mm  Maximum stress = 60 MPa

Q: Problem 3 The tube shown below has a uniform wall thickness of 12 mm. For the loading given,…

A: We have to determine the value of stress at point A and B in the given figure according to the given…

Q: For question 103A and 103B, the thin-walled cylindrical container shown below. Say p is the internal…

A: Given data:Internal pressure, p=15 MPa or 15 N/mm2Inside diameter, d=20 mmWall thickness, t=10…

Q: A strain gage is mounted at an angle of 30° with respect to the longitudinal axis of the cylindrical…

A: Diameter of cylinder = 54 inch  Internal pressure = 0.702 ksi  E= 10000 ksi  v= 0.33

Q: Calculate the minimum wall thickness (in) for a cylindrical vessel that is to carry a gas at a…

A:

Q: A spherical pressure vessel has an inside diameter of 6 m and a wall thickness of 15 mm. The vessel…

A: Given: Spherical pressure vessel  Inside diameter  Thickness  Internal pressure  Yield strength

Q: Calculate the minimum wall thickness for a cylindrical vessel that is to carry a gas at a pressure…

A:

Q: A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is subjected…

A: Given data -  Cylindrical steel vessel  Diameter (D) = 400mm Wall thickness(t) = 20 mm Internal…

Q: A cylindrical tank holding oxygen at 2.091 kPa pressure has an outside diameter of 409 mm and a wall…

A:

Q: Find maximum shear stress in the wall?

A: Given, Cylindrical tank inner radius,r= 14 m Thickness,t= 60 mm Gauge pressure,P= 3 MPa Find maximum…

Q: A steel cylindrical pressure vessel at an industrial plant has a diameter of D = mm. The cylinder…

A:

Q: A compound shaft consists of a titanium alloy [G = 6,200 ksi] tube (1) and a solid stainless steel…

A:

Q: at pulley C so that the rotation angle of pulley C relative to A is zero.

A:

Q: Problem 1: Given the axially-loaded compound shaft, determine the axial stress developed in each…

A:

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?