A submersible cylinder used in research has a cylindrical pressure hull of outside diameter 3.0 m and a wall thickness of 150 mm. It is constructed of an aluminum alloy, having a yield point of 450 MPa. Determine the tangential stress, in terms of MPa, in the cylindrical portion of the pressure hull when the vehicle is at its operating depth of 5500 m below the surface of the sea. Consider sea water to have a specific weight of 104 N/m3

A submersible cylinder used in research has a cylindrical pressure hull of outside diameter 3.0 m and a wall thickness of 150 mm. It is constructed of an aluminum alloy, having a yield point of 450 MPa. Determine the tangential stress, in terms of MPa, in the cylindrical portion of the pressure hull when the vehicle is at its operating depth of 5500 m below the surface of the sea. Consider sea water to have a specific weight of 104 N/m3

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter3: The Structure Of Real Materials

Section: Chapter Questions

Problem 3.12P

See similar textbooks

Similar questions

Qs
Pls answer 3-5
Consider a pressure vessel that is made of two half-spherical domes with 1 ft in diameter, and the cylinder portion is 3 ft in length and is subjected to 100 psi pressure. The maximum tensile strength of the material is 55 ksi. The factor of safety for this design is 1.5. Problem: Determine the minimum thickness for this design.
THIN WALLED PRESSURE VESSELS SITUATION: A cylindrical water tank is 8 m in diameter and 12 m long. The material stress is limited to 40 MPa. If the tank is to be completely filled determine the following: 3. Thickness of the tank plating in mm if subjected to longitudinal stress 4. Thickness of the tank plating in mm if subjected to circumferential stress. 5. Minimum required thickness to be purchased if the material is sold in 2mm increments.
Water from a reservoir flowing through a deformable 600mm diameter pipe with a velocity of 2.5m/s is completely stopped by a closure of a valve situated 400m from the reservoir. Assume that the pressure increases at a uniform rate and that there is no damping of pressure wave. The pipe has a thickness of 20mm. Bulk modulus of water is 2.20x10°Pa and modulus of elasticity of steel is 0.14x10 Pa. Find the water hammer pressure for instantaneous valve closure.
A cylindrical boiler with an outside diameter of 2.55m and a wall thickness of 27mm is made of a steel alloy that has a yield stress of 300MPA. Determine: (a) the maximum normal stress produced by an internal pressure of 1.7MPa. (b) the maximum allowable pressure if a factor of safety of 2.5with respect to yield is required. Answers: MPa (a) Omax" MPa (b) Pallow"
A spherical pressure vessel of 900 mm outer diameter is to befabricated from a steel having an ultimate stress, σ U = 400 MPa.Knowing that a factor of safety of 4 is desired and that the gaugepressure can reach 3.5 MPa, determine the smallest wall thicknessthat should be used.
A 1.8 m dia. by 2.7 m high closed cylinder is fully filled with glycerin having sp.gr. of 1.6 under a pressure of 245 kPa at the top. The steel plates which form the cylinder is 5 mm thick with 82 MPa as its ultimate tensile stress. How fast can it be rotated (rpm) at its vertical axis to the point of bursting?
STRENGTH OF MATERIALS A boiler is constructed of 9mm thick steel plates that are fastened together at their ends using a butt joint consisting of two 9mm cover plates and rivets having a diameter of 10mm and spaced 60mm apart as shown. If the stream pressure in the boiler is 1.38MPa, determine (a) the circumferential stress in the boiler's plate apart from the steam, (b) the circumferential stress in the outer cover plate along the rivet line a-a, and (c) the shear stress in the rivets. 60 mm 0.78 m
7. An undersea research vehicle has a spherical hull of I m radius and 4() mm thickness. The hull is constructed of high strength alloy steel having a yield point of 700 MPa. Neglecting the adverse effect of cnti-ance ports cut into the hull determine the depth the vessel may be submerged to set up a stress equal to that of the yield point Note: Relative Density of sea water. = 1.023
PLEASE ANSWER
A load of 1950N is raised at the end of a steel wire. The minimum diameter of the wire so that stress in the wire does not exceed 100 N/mm2