THIN WALLED PRESSURE VESSELS SITUATION: A cylindrical water tank is 8 m in diameter and 12 m long. The material stress is limited to 40 MPa. If the tank is to be completely filled determine the following: 3. Thickness of the tank plating in mm if subjected to longitudinal stress 4. Thickness of the tank plating in mm if subjected to circumferential stress. 5. Minimum required thickness to be purchased if the material is sold in 2mm increments.

THIN WALLED PRESSURE VESSELS SITUATION: A cylindrical water tank is 8 m in diameter and 12 m long. The material stress is limited to 40 MPa. If the tank is to be completely filled determine the following: 3. Thickness of the tank plating in mm if subjected to longitudinal stress 4. Thickness of the tank plating in mm if subjected to circumferential stress. 5. Minimum required thickness to be purchased if the material is sold in 2mm increments.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

From the rectangular area shown a semi-circle of radius 4 cm is removed. Locate the centroid, (C), of the remaining area.
QUESTION 4 Table Q4 shows the booking of levelling fieldwork conducted during light rain. It was later found out that some of the readings are illegible due to the rain water. Complete the booking and perform all checks. Table Q4 BS IS FS HPC RL Remarks ? 20.662 18.569 TBM 1 RL 18.569 2.010 ? ? 18.645 3.467 0.418 20.244 C (CP) 3.053 ? D E TBM 2 RL 22.968 1.467 22.243 22.959 !! IMPORTANT ! SAVE THIS QUESTION PAPER (SHADED AREA) IN PDF AND SUBMIT IT TO THE E-LEARNING WEBSITE
* Fill the missing reading Point B.S I.S F.S R+ F- R.L Remark 1.25 ? 0.93 1.78 1.93 1.91 1.27 ? 0.05 30.09 В.М 1.61 ? 0.18 1.27 Point B.S I.S F.S R+ F- Point B.S I.S F.S R+ F- 1.25 A 1.25 (2.18) 0.93 (2.18) 0.93 1.93 (0.25) 1.27 (0.51) 1.78 C 1.78 1.93 (0.25) 1.91 D 1.91 1.27 (0.51) (1.86) E (1.86) 1.61 E 0.05 0.05 F 1.61 (0.25) F (0.25) |(1.43) (2.7) (1.43) 0.18 0.18 H (2.7) 1.27 H. 1.27 1 0 3 Point B.S I.S F.S R+ F- A 1.25 (0.32) 0.93 1.93 (1.61) 1.27 (0.51) C 1.78 D 1.91 E (1.96) 0.05 F 1.61 (0.25) G (1.43) 0.18 H (2.7) 1.27 2 O ABCDEFGH
Determine the y-coordinate of the centroid of the shaded area. y 0.25h 69° 69° Answer:y = i h Save for Later Attempts: 2 of 3 used Submit Answer
If gage A reads-20 kpa, determine the elevations of points L, N, Q, Z
PROBLEM SOLVING Analyze this problem and complete the level note with customary arithmetic check. 8.89 3.46 7.75 1.83 BM No. 4 10.34 1.37 9-7 (H)2.64 TP, 2.178.57 (H) 8.56 [11.14 TP, 1-89 CH) BM No. 3 elevation 441.72 ft
Review Problem (Situation 9) Locate the centroid of the given area.
Q.I A line of level is run from B.M.I (elevation=106.40m) to B.M. 2(elevation=110.50m). The field observations were recorded as given helow: Station B. S 1.95 Remarks R.M. 1 IS F.S 2 0.65 3 2.60 1.45 4 -1.90 -1.60 0.55 0.50 B.M. 2 Reduce the level of point 2, 3, 4 and 5, determine the total error of closure, and adjust the values.
Correct answer is 9,872.198 kN. No other answer thanks
P1
1-11 Relative position between lines and planes 1. Find the intersection point K between given line and plene, then escertoin visibility of question (1). (1) (2) 2 Fnd the intersection point K between given line and plane, then ascertein visibility of them 3. Find point collection which has equal distance from point A and B.
ractical Part 6/ Find the Elevation in the point (B). A BS 12.64 Elevation 100.00 FS 3.11 BS 10.88 TP₁ FS 2.56 BS 9.72 TP2 FS 3.10 B