The gas storage tank is fabricated by bolting together two half cylindrical shells and two hemispherical shells as shown in Figure 4. The tank and the 25 mm diameter bolts are made from material having an allowable hormal stress of 150 MPa and 250 MPa, respectively. The tank has an inner diameter of 4m. If the tank is lesigned to withstand a pressure of 3 MPa, a. Determine the required minimum thickness of the cylindrical and hemispherical shells b. Determine the minimum required number of bolts for each hemispherical caps.

The gas storage tank is fabricated by bolting together two half cylindrical shells and two hemispherical shells as shown in Figure 4. The tank and the 25 mm diameter bolts are made from material having an allowable hormal stress of 150 MPa and 250 MPa, respectively. The tank has an inner diameter of 4m. If the tank is lesigned to withstand a pressure of 3 MPa, a. Determine the required minimum thickness of the cylindrical and hemispherical shells b. Determine the minimum required number of bolts for each hemispherical caps.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 4 The brass bar shown is loaded axially in compression so that the maximum stress induced is 125…

A: Maximum stress = 125 MPaDiameter, D = 30 mmhole diameter, d = 20 mmModulus of elasticity, E = 100…

Q: please solve the following problem with paper and pencil and please show the correct answer and step…

A: Given: L = 28 feetE = 29 x 103 ksi The column height at length L= 28 feet. To simplify calculations,…

Q: 1.) A STEEL WIRE 30 ft LONG HANGING VERTICALLY SUPPORTS A LOAD OF 500 lb. 30 ft NEGLECTING THE…

Q: A Sandwich block is comprised of brass in the centre with two aluminium plates attached to either…

Q: Item 2 The gas storage tank is fabricated by bolting together two half cylindrical thin shells and…

A: Given : The tank designed to withstand pressure of 3 MPa Allowable normal stress of tank material =…

Q: The brass shell (ab = 20.9 × 10-6/°C) is fully bonded to the steel core (as = 11.7 × 10-6°C).…

A: Step 1:Step 2:

Q: 5. Determine the critical stress in the tube column shown below. The column has a height of 28 feet;…

Q: I need the answer as soon as possible

A: Given data:- Cross-section of plate is 0.5 m × 0.3 m Thickness of plate is 0.01 m Young's Modulus…

Q: A copper bar is of uniform cross-section and is rigidly attached to the walls as shown. The rod is…

Q: Question 4. Three wires are used to suspend the plate shown. Aluminium wires used at A and B with a…

Q: Q2 - The assembly shown below consists of three rods AB, CD and EF with the following properties: AB…

Q: Problem #2: A steel bolt with a diameter of 8 mm fits through an aluminum sleeve with and outer…

Concept explainers

Pressure and Stress

Question

The gas storage tank is fabricated by bolting together two half cylindrical shells and two hemispherical shells
as shown in Figure 4. The tank and the 25 mm diameter bolts are made from material having an allowable
normal stress of 150 MPa and 250 MPa, respectively. The tank has an inner diameter of 4m. If the tank is
designed to withstand a pressure of 3 MPa,
a. Determine the required minimum thickness of the cylindrical and hemispherical shells
b. Determine the minimum required number of bolts for each hemispherical caps.
Figure 4

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. Show your complete solution
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 78 GPa. Thesteel rod has a diameter of 16 mm and an elastic modulus of E = 200 GPa. Assume a = 4.1 m, b = 1.2 m, and c= 1.2 m. What is the magnitude of load P that is necessary to displace point A 12 mm to the left? (1) P (3) B (2) Answer: P = 117.7 kN
Full solution.
1. The assembly has the diameters and material makeup indicated. If it fits securely between its fixed supports when the temperature is T; = 70°F, determine the average normal stress in each material when the temperature reaches T2 = 130°F. 304 Stainless steel - 2014-T6 Aluminum -C 86100 Bronze A 12 in. 8 in. D C 4 in. -4 ft- 6 ft- 3 ft
#2 will upvote to anyone who will answer
A hydraulic punch press is used to punch a slot in a 10-mm-thick plate, as illustrated. If the plate shears a determine the minimum force P required to punch the slot. Punch O 1051 KN O 766 kN O 649 kN O 717 KN O 979 KN Slug Plate 20 mm 75 mm Plan view of slug + a stress of 360 MPa,
A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, s,, = 345 MPa) for %3D the C-frame material. Calculate the location of centroidal axis upto 2 digits after decimal point in mm? 18 mm 38 mm 13 kN 25 mm 10 mm 90 mm A+ A 10 mm
solve thee following problem with the correct answer please, please make sure to show so I can understand.
Three identical circular A36 steel columns, A, B, and C, are carrying a 750kN block. The diameter of each column is 30mm. Calculate the normal stress on each column when column B is heated from 20oC to 25oC. Consider: EA36 =200GPa  A36 =0.000012 oC-1 1) What is the effect of column length on the result? 2) Is this structure statically determinate or indeterminate? Why?
A polymer cylinder (2) is clamped between rigid heads by two steel bolts (1). The steel [E = 29,000 ksi; a = 6.5x10-6/°F] bolts have a diameter of 0.30 in. The polymer [E = 370 ksi; a = 38.3x 10-6/°F] cylinder has an outside diameter of 6.6 in. and a wall thickness of 0.75 in. Assume a = 29 in. and b = 37 in. If the temperature of this assembly changes by AT = 135°F, determine: (a) the normal stress in the polymer cylinder. (b) the normal strain in the polymer cylinder. (c) the normal strain in the steel bolts. %3D %3D %3D %3D (1) C (2) a (1) b. Answer: (a) 02 = psi. (b) E2 = 3d (c) E1 =
1/2 Problem 1: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown in. If the stress must not exceed 14OMPA in either rod, determine the smallest allowable value of the diameter of rod AB and ВС. 300mm B 40 kN 250mm - d2 30 kN