10.15 - A three-phase dc/ac converter is used to power a three-phase, Y-connected, resistive load of 50 (per phase). The de voltage is 150 V. Compute the following: a. The frequency of the ac waveform if the time interval is 100 us. b. The current of the dc source. c. The rms current of the load. d. The rms of the line-to-line voltage across the load.

10.15 - A three-phase dc/ac converter is used to power a three-phase, Y-connected, resistive load of 50 (per phase). The de voltage is 150 V. Compute the following: a. The frequency of the ac waveform if the time interval is 100 us. b. The current of the dc source. c. The rms current of the load. d. The rms of the line-to-line voltage across the load.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.1MCQ: The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax

See similar textbooks

Similar questions

A chopper circuit drives an inductive load from 390 DC supply. Given the load resistance as 8 Q, the average load current as 23 A and operating frequency is 480 Hz. When the chopper is ON, 7 V is dropped. Calculate (a) conduction period (in milliseconds) (b) blocking period of the chopper (in milliseconds) (c) duty cycle of the chopper (d) draw the ON and OFF time period waveform (ii) Draw the circuit diagram of the single phase bridge rectifier which is used in two quadrant operation (RL load) and explain its operation.
Please and thank you
Another name for the RMS value of current or voltage is ... O the effective value O the exact value O the true value O the reactance value
Question-3 Can you throw the emergency solution? I would appreciate it if you write legibly.
Derive the average and rms values of output voltages and currents for three phase semi converter. Power Electronics
Q1. What is the principle of Buck-Boost type DC-DC converter? Derive the expression of voltage gain of it. A buck type converter is connected to a PV module, a 60 2 of load impedance and operated at a duty cycle of 45%. What would be the reflected impedance? If the PV module's voltage will be 26.8 Voltage. Find the current of it.
Pls answer d. Only
١-The PMSM used in the industry due to: a- Their low noise. b- Their easy control arrangement. c- Their efficiency. 2- The BLDCM used in the industry due a- Their low noise. b- Their easy control arrangement. - Their efficiency. 3- The (PMSM) supplied by: a- DC voltage. b- AC voltage of sinusoidal waveform. C- AC voltage of trapezoidal waveform. Choices
1) The current and voltage waveforms given in the figure on the right.power electronics converter to which the shapes belongDraw the circuit. The stress on the load andThe relations for the average value of the current are obtained.please. 2) Positive half wave of AA voltage transferred to the loadfixed negative half wave is a controllableDraw an AA phase control circuit. Pure ohmic load and ?output current and voltage for a trigger angle such asGive the waveforms. 0 <? <pi
While Thevenizing a circuit between two . . terminals, VTH is equal to * rms voltage available in the circuit. O short circuit terminal voltage. O net voltage available in the circuit. O open circuit terminal voltage. )
Solve it quickly please
EX1: The AC Voltage controller shown below is used for heating a resistive load of 5 N and the input voltage Vs = 120 V (rms). The thyristor switch is on for n=125 cycles and is off for m = 75 cycles. Determine the RMS output voltage Vo, the input factor and the average and RMS thyristor current.