From the image answer the following:1. Calculate the (lagging) power factor of the total load of the plant in the image2. A capacitor bank will be installed in parallel to the loads to improve the power factor of the total load. How much Reactive Power in kiloVAR will the capacitor bank have to supply to improve the power factor to 98%, lagging? A small manufacturing plant has the following connected loads:Load 1 (L1): lighting/outlet/appliances4,500 W at 0.85 pf LAGLoad 2 (L2): compressor motors/pumps37,300 W at 0.75 pf LAGLoad 3 (L3) : heatersAssume that the capacitor bank is installed only for question 5.15,000 W at 0.95 pf LAGVsource440 VAC (rms)60 HzL1L2L3Capacitor Bankforpower factorimprovement

Answered: Image /qna-images/answer/9d20969c-10dc-43c8-bd7f-43deb98852e5.jpg

A small manufacturing plant has the following connected loads: Load 1 (L1): lighting/outlet/appliances 4,500 W at 0.85 pf LAG Load 2 (L2): compressor motors/pumps 37,300 W at 0.75 pf LAG Load 3 (L3) : heaters Assume that the capacitor bank is installed only for question 5. 15,000 W at 0.95 pf LAG Vsource 440 VAC (rms) 60 Hz L1 L2 L3 Capacitor Bank for power factor improvement

A small manufacturing plant has the following connected loads: Load 1 (L1): lighting/outlet/appliances 4,500 W at 0.85 pf LAG Load 2 (L2): compressor motors/pumps 37,300 W at 0.75 pf LAG Load 3 (L3) : heaters Assume that the capacitor bank is installed only for question 5. 15,000 W at 0.95 pf LAG Vsource 440 VAC (rms) 60 Hz L1 L2 L3 Capacitor Bank for power factor improvement

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

Match the following: (i) Hysteresis loss (a) Can be redud by constructing the core with laminated sheets of alloy steel (ii) Eddy current loss (b) Can be reduced by the use of special high grades of alloy stl as core material.
10. Determine the peak-to-peak ripple and de output voltages in Figure 5. The transformer has a 36 V rms secondary voltage rating, and the line voltage has a frequency of 60 Hz. A R surge 120 Vrms 00000 ellle B Figure 5. www 10 Ω C 100 μF www R₂ 3.3 ΚΩ
ings of a 40 kVA, 6 m respectively. The le- ate (i) the primary vol ced (ii) the full-load re
QUESTION 19 E-06, PC-02. Three inductors 15 mH, 15 mH and 15 mH are connected in series. What is the total inductance? O 5 mH. Without knowing the coupling factor the total inductance cannot be found. 45mH. QUESTION 20 E-06, PC-05. Why are the iron cores of most induction coils laminated? To increase the core permeability. O To reduce the core reluctance. O To reduce the effects of eddy currents. Click Save and Submit to save and submit. Click Save All Answers to save all answers. MacBook Air 888 F7 FB F6 F4 F3 F2 & 23 $ 4 5 0 8 3 Y W E と S D S F G >> J しのくつつ >
Match the corresponding connections. The Capital letters represent Primary side, and the lower case letter represent secondary side. Three Phase Transformer Name Graph Three Phase Transformer 1 Three Phase Transformer 2 B ÏA ΝΑ IB NB Je elle elle 0000 0000/ • elle I b Na Nb b le c
Number 11 and 12 how do I figure those out.
QUESTION 14 A 900nF capacitor, a 200mH inductor and an 8200 resistor are connected in parallel with a function generator. The total voltage for the circuit is 120V RMS, 550HZ. Calculate the total impedance, total current, and the current through each component. Show all of your work, including circuit diagram. Write out your solution by hand and take a scan/photo of your work. Submit your work for Question 14 here. Make sure your submission is neat and legible. No marks will be allocated for significant digits.
(5) Primary AC Source Transformer Secondary AC/DC Full-wave Rectifier Capaictor in Non- linear Load Figure 6 Analyse different methods of harmonics mitigation to eliminate the harmonic, which you have identify in above power system circuit. You can use harmonic filters, K or equivalent transformers or oversized neutral method depending upon the harmonic sources.
What will be the value of the twiddle factor: W42
You are an electrician working in an industrial plant. A 30-hp three-phase induction motor has a current draw of 36 amperes at full load. The motor is connected to a 480-volt line. A three-phase wattmeter indicates a true power of 22 kW. Determine the power factor of the motor and the amount of capacitance needed to correct the power factor to 95. Also determine the minimum voltage rating of the capacitors. The capacitors are to be connected in wye.
What is the advantage of a diverter across the series field in compound generator
A three phase power transformer having a line voltage ratio of 400 V to 33 kV is connected in star-delta. The C.T.s on 400 V side have current ratio as 1000/5. What must be the C.T. ratio on 33 kV side. Assume current on 400 V side of transformer to be 1000 A. C.T. secondaries in delta p 5A oooo oooo 5√3 A -0000 0000 0000 0000 Star-delta transformer 0000 5√3 A vooo னள். m reeee p C.T. secondaries in star 5√3 A 0000