A single phase transformer rated 100 KVA, 2.4 KV/240V. If 240 V winding is short-circuited, the rated current flows when the voltage applied 2.4 KV winding is 1.054 KV. The power input is 3.89 KW. What is the value of the reactance referred to high- voltage winding? A. 26.2 B. . 24.2 C. 25.2* D. 22.5

A single phase transformer rated 100 KVA, 2.4 KV/240V. If 240 V winding is short-circuited, the rated current flows when the voltage applied 2.4 KV winding is 1.054 KV. The power input is 3.89 KW. What is the value of the reactance referred to high- voltage winding? A. 26.2 B. . 24.2 C. 25.2* D. 22.5

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.11MCQ: For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the...

See similar textbooks

Similar questions

Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
a. The core of a three phase, 50 Hz,11000/550 V delta/star, 300 kVA, core-type transformer operates with a flux of 0.05 Wb.Find (i) number of H.V and L,V turns per phase, $(ii)$ e.m.f per turn (iii) full load H.V and LV turns per phase.
Please solve the problem i want urjent
Solutions please
9
Following are the results of a test carried out on a 230/600 V single phase, 7.5 kVA transformer. O.C. Test : 230 V, 1.2 A, 280 W, on L.V side S.C. Test : LV winding is shorted. 26 V, 11A, 155 W, H.V. Both the full load efficiency and full load regulation of the transformer on the side are 0.8 lagging p.f Search on.
A single-phase 100 kVA, 2400/240 V, two-winding transformer will be used as a step-down auto-transformer in a 2640/2400 V system. The connection diagram of the transformer is given below. Calculate the I1, I2 and Ix currents given in the figure. Compare the kVA values of the auto transformer with the kVA values of two-winding transformers.
A voltage transformer in Figure 8 has 1,500 turns of wire on its primary winding and 500 turns of wire for its secondary winding. What will be the turns ratio, a of the transformer. If 240 volts is applied to the primary winding, what will be the resulting secondary voltage. And if a 400 n resistor is connected to the secondary winding, what are the values of current Is and Ip. primary Vp Transformer Core NF Ns Figure 8 secondary Vs
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.
Two 11,000/2,200-V, 1-phase transformers are connected in parallel to supply a total load of 200 at 0.8 p.f. lagging at 2,200 V. One transformer has an equivalent resistance of 0.4 ohms and equivalent reactance of 0.8 ohms referred to the low-voltage side. The other has equivalent resistance of 0.1 ohms and a reactance of 0.3 ohms. Determine the current and power supplied by each transformer.