Remove the 50 resistor in the given circuit and assume an operating frequency of 50 Hz and a load of 100 Q connected between terminals a and b. In the given circuit /x=8.0040° A. 160 Ω ell 50 Ω 809 1x b Determine the capacitance that must be connected between the terminals marked a and b to increase the PF of the source to 0.95. (Round the final answer to four decimal places.) The capacitance that must be connected between the terminals marked a and b is 66.182 µF.

Remove the 50 resistor in the given circuit and assume an operating frequency of 50 Hz and a load of 100 Q connected between terminals a and b. In the given circuit /x=8.0040° A. 160 Ω ell 50 Ω 809 1x b Determine the capacitance that must be connected between the terminals marked a and b to increase the PF of the source to 0.95. (Round the final answer to four decimal places.) The capacitance that must be connected between the terminals marked a and b is 66.182 µF.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter26: Three-phase Circuits

Section: Chapter Questions

Problem 3PA: You are an electrician working in an industrial plant. A 30-hp three-phase induction motor has a...

See similar textbooks

Similar questions

What's 21 22 23
If a circuit has a resistance of 3002 and a series inductance of 5002, what is the relationship between the applied circuit voltage and the circuit current? The applied voltage lags the circuit current. The phase shift between the circuit voltage and current changes with time. The applied voltage is in phase with the circuit current. The applied voltage leads the circuit cur Previous Page Next Page Page 2 of 10
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
Comment on how a change in frequency will affect the currents in both figure 6 and figure 7.
need part a, b and c asap i willl give you upvote
AC Circuits Sine-wave generator f- 25 kHz V₁ = 3.0 V VR 888 100 mH Figure 6-Test Circuit 3. Using a two-channel oscilloscope, measure the peak-to-peak voltage VR across the resistor and the peak-to-peak voltage VL across the inductor. Measure the voltage across the inductor using the difference technique described in a previous experiment. Record the voltage readings in Table 2. VL 10 k 1 XL Table 2- Measured and Calculated Values (f = 25 kHz) ZT
1. Find the average value of current when the current that are equidistant are 4A, 5A and 6A. a) 5A b) 6A c) 15A d) 10A
For the series RL circuit shown in the figure below, answer the following questions and justify your answer.If the current is kept constant, does the coil have inductance?If the current is kept constant, does the coil affect the current value?Can the reverse emf ever be greater than the battery emf?
A moving coil ammeter and a moving iron ammeter are connected in series with arectifier across 110V (r.m.s.) AC supply. The total resistance of the circuit in theconducting direction is 60 ohm and that in the reverse direction may be taken asinfinity. Assuming the waveform of the supply voltage to be sinusoidal, calculate thereadings in each ammeter
= For the given figure, eo/ei
QUESTION 3 An inductor and a 330 ohm resistor are connected in series with a function generator. The current is 89.8mA RMS 5kHz. The reactive power is 3.04 var. Find the value of the inductance. O 12mH O 24mH O 6mH O 18mH
With V1, voltage peak to peak is 10 volts, R1=200 Ohm, R2=1000 Ohm and C1= 300 nF. Find Vx, voltage across the the capacitor, C1 and R2 when the frequency is 1000 Hz and 10000 Hz