000 The 1st-order RC Lowpass Filter circuit was found in class to have the following unit step response for T = RC = 1: s(t)=lu (t) — e-*u (t) If an input signal x (t) = 4rect (t - 0.5) - 4rect (t - 1.5) is applied to this system when it is relaxed, select ALL of the terms below that will appear in the total response of the system to this new input: 48 (t) (4-4e-')u(t) (4-4e-(-0.5)) u (t - 0.5) (-4+4e-(-1)) u (t − 1) (-88e-(-1)) u (t - 1) (-4+4e-(-1.5)) u (t - 1.5) (-4+4e-(-2)) u (t − 2) (4-4e-(-2)) u (t-2) -88 (t-1) 48 (t - 2)

000 The 1st-order RC Lowpass Filter circuit was found in class to have the following unit step response for T = RC = 1: s(t)=lu (t) — e-*u (t) If an input signal x (t) = 4rect (t - 0.5) - 4rect (t - 1.5) is applied to this system when it is relaxed, select ALL of the terms below that will appear in the total response of the system to this new input: 48 (t) (4-4e-')u(t) (4-4e-(-0.5)) u (t - 0.5) (-4+4e-(-1)) u (t − 1) (-88e-(-1)) u (t - 1) (-4+4e-(-1.5)) u (t - 1.5) (-4+4e-(-2)) u (t − 2) (4-4e-(-2)) u (t-2) -88 (t-1) 48 (t - 2)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If you want a band-pass filter with cut-off frequencies at 5 Hz and 50 Hz what is the transfer function of the filter. Give your answer to 4 significant figures.
Design a low-pass filter using a 100 mH inductor and a single resistor R to obtain a cutoff frequency of 7500 Hz ± 2%. In your notebook, show your design procedure, including your design calculations Can you do this written out please anf thank you!
Need help steps would be helpful please and thank you!
The following figure shows a system that couples an inverting band pass filter with a high pass filter. Using parameters given in the figure, derive the transfer function of Vo(s)/Vi(s) Vi Inverting band pass filter R₁ ww C₁ C₂ R₂ High pass filter C3 R3 R4 R5 Vo Hint: You could start with writing the transfer function of the two filters separately, then combine the two equations into one. Your transfer function may be written as the product of multiple filters and/or gain stages - you do not need to reduce to simplest form but you should have each piece derived somewhere.
Answer the following with illustration and solutions. 2. Design a basic wide-band, RC band stop filter with a lower cut-off frequency of 250 Hz and a higher cut-off frequency of 1.2kHz. Find its center frequency, bandwidth and Q of the circuit assuming the capacitor for both filter sections is 0.1 microfarad. Thia is the example that might help.
What type of passive filter does this circuit represent and what is the cutoff frequency?
As part of a radio receiver, you are asked to design a simple bandpass filter using a series inductor, capacitor and resistor. The filter needs to pass a centre frequency of f0 = 1089 kHz with a bandwidth of 9 kHz. Do this by finding the capacitor and resistor values together with a 240 uH inductor that will give you the correct centre frequency and bandwidth. Also, calculate the quality factor Q for your filter. Sketch the filter circuit and show all your calculations.
Q5) Find the transfer function in the following circuit VO/Vi. Draw its frequency response vs Omega (approximation is ok). What kind of filter is this circuit? Low pass/High pass/ Bandpass Write the equation for its cutoff frequency. R M BiwL + VƏ
For the circuit in the following figure, obtain the transfer function Vo(@)Vi(@). Identify the type of filter the circuit represents and determine the corner frequency. Take R1=100 =R2, L=2 mH. vi(t) (+ R₁ ele L R₂v(t) vo(t) 10+
plz provide answer for ques6 part a and d
Explain nicely and write clearly Answer Correctly Completely Answer only if you are sure I will like you on your answer and invite my colleagues also Thank you :)
3. Active Analog Filter Topologies You already know from our class discussions that Circuit 1 is an active analog Low-Pass Filter For each of the remaining three circuits, state whether the circuit will function as a low-pass or high-pass filter. Each of your answers must be accompanied by a brief explanation and justification incorporating the frequency dependent characteristics of the reactive circuit elements. That is you should look at the asymptotic impedance of the L and C if the input signal the frequency is very low or very high. Sketch the expected Bode plot for 20 log(Vo/Vs) as a function of log (f) labeling the corner frequencies. No equations are required! R2 R2 R2 R2 R1 R1 R1 Vs Vs o W- Vs Vs Vo Vo Vo Vo Circuit 1 Citcuit 2 Circuit 3 Circuit 4