8262.5 ▸ A balanced star connected load is connected to a 4 kVA, 415 V, star connected three phase generator via a three wire transmission line. The impedance of each line is 0.3 + j6.0 ohms. The synchronous impedance of the generator is 0.4 + j2.4 ohms. The fixed losses of the generator are 175 W. The field winding is connected to a 120 V source and the field current is 5.5 A. When the generator delivers rated load at rated voltage and at 0.866 power factor lagging, find ▸ The efficiency of the generator (79.8%) The voltage regulation at the load (11.2%) ▸ The efficiency of the entire system. (79.2%) Ts = 8262.5w (401) =65.74 N.m ▸ Draw the power flow diagram of the entire power system indicating on the diagram all the values of the power flows.

8262.5 ▸ A balanced star connected load is connected to a 4 kVA, 415 V, star connected three phase generator via a three wire transmission line. The impedance of each line is 0.3 + j6.0 ohms. The synchronous impedance of the generator is 0.4 + j2.4 ohms. The fixed losses of the generator are 175 W. The field winding is connected to a 120 V source and the field current is 5.5 A. When the generator delivers rated load at rated voltage and at 0.866 power factor lagging, find ▸ The efficiency of the generator (79.8%) The voltage regulation at the load (11.2%) ▸ The efficiency of the entire system. (79.2%) Ts = 8262.5w (401) =65.74 N.m ▸ Draw the power flow diagram of the entire power system indicating on the diagram all the values of the power flows.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.23MCQ: Does an open- operation, the kVA rating compared to that of the original thr-phase bank is (a) 2/3...

See similar textbooks

Similar questions

Single phase non-ideal transformer. Turn Ratio= 3000/600. R₁ = 0.9Q R₂= 36 mQ Ro= 3000 Q X₁₁ = 0.6Q X12= 0.0024 Q X0= 6000 Q Input voltage-1440 V (also known as rms voltage) Load impedance of secondary winding is z₂= 0.12 + j0.3 Q a) Secondary winding current phasor 12 (NOT to be confused for I'₂) b) Load voltage phasor V2 (NOT to be confused for V'2) c) Primary winding current phasor ī₁ → X11 X12 R₁ R'2 www V₂ V₁ ī₁ R m ×°
I need the answer quickly
The rated voltages of a single-phase transformer are 2000 V and 200 V in its primary and secondary respectively. The shunt impedance can be modelled with a resistance of 14000 ohms in parallel with a reactance of 1100 ohm, both refer to primary side. The primary and secondary series impedances are (0.12+j 0.35) ohms and (0.0012+j 0.0035) ohms respectively. A load is connected to the secondary side of transformer, draws 810 KVA with a lagging power factor of 0.85. The load voltage is same as rated voltage, that is 200 V. ▪ Use per unit method for analysis and find the voltage on primary side in pu.
2) 9.2Three - 25 KVA single-phase transformers are connected in delta – delta. One of the transformers has been defected. What is the maximum real power that the transformer bank can deliver at a power factor of 0.8?
sformer 1200 KVA, 11000/2200 V, 50 Hz e reactance/phase of the primary winding ar ding values for the secondary winding are C primary winding is connected in delta and
A generator supplies a motor through a Y-A transformer. The generator is connected to Y side of the transformer. A fault occurs between the motor terminals and the transformer. The symmetrical components of the subtransient current in the motor flowing toward the fault are: I =-0.8- j2.6pu I =-j2.0pu I =-j3pu From the transformer toward the Fault: I = 0.8– j0.4pu I? =-j1.0pu 1 = Opu Assume X =X,=X, for both the motor and the generator. (a) Describe the fault type and find the prefault current, if any, in line a. (b) Determine the subtransient fault current in per unit. (c) Calculate the subtransient current in each phase of the generator in per unit taking into consideration the phase shift of the Y-A transformer.
An 11 kV generating station has four identical 3-phase alternatorsGl, G2, G3 and G4 each of L0 MVA capacity and l2%o reaclarce.There are two section of bus-bar P and Q, linked by a reactor X ratedat 10 MVA with 24o/oreactance. From section Q load is taken througha 6 MVA, i 1kV/66kV step-up transformer (T1) having a reactance of37o. Determine the fault current if a three-phase short-circuit occursnear the high voltage terminal of the transformer (F) as shown inFigure.Assume prefault voltages to be 1 pu and prefault currents to be zero
A three phase power transformer having a line voltage ratio of 400 V to 33 kV is connected in star-delta. The C.T.s on 400 V side have current ratio as 1000/5. What must be the C.T. ratio on 33 kV side. Assume current on 400 V side of transformer to be 1000 A. C.T. secondaries in delta p 5A oooo oooo 5√3 A -0000 0000 0000 0000 Star-delta transformer 0000 5√3 A vooo னள். m reeee p C.T. secondaries in star 5√3 A 0000
Three single phase transformers are connected in a Delta-Wye configuration. Each transformer is rated 13kV/64kV. The transformers are connected to a 3 phase 13kV (L-L) supply and the balanced three phase load is 788KVA. What is the current magnitude in the secondary winding of each transformer? explain the steps too please
A three-phase transformer bank is connected wye–delta. The primary voltage is 12,470 V, and the secondary voltage is 480 V. The total capacity of the transformer bank is 450 kVA. One of the three transformers that form the three-phase bank develops a shorted primary winding and becomes unusable. A suggestion is made to reconnect the bank for operation as an open-delta. Can the two remaining transformers be connected open-delta? Explain your answer as to why they can or why they cannot be connected as an open-delta. If they can be reconnected open-delta, what would be the output capacity of the two remaining transformers?
transformer 1200 KVA, 11000/2200 V, 50 Hz." akage reactance/phase of the primary winding are sponding values for the secondary winding are 0. f the primary winding is connected in delta and s- oltage to be applied at normal frequency to the ad through it when the secondary is short-circui all load copper loss pr
Single phase non-ideal transformer. Turn Ratio= 3000/600. R₁ = 0.9Q R2= 36 mQ Ro= 3000 Q X₁₁ = 0.60 X12= 0.0024 02 X= 6000 Input voltage= 1440 V (also known as rms voltage) Load impedance of secondary winding is Z₂= 0.12 + j0.3 a) Copper losses on primary and secondary windings b) Core loss c) Transformer efficiency V₁ Ī₁ Ro ww m Xu R₁ R'2 ww m ww I₂ X12 m