1. Find the flow distribution in the three-parallel pipe system shown in figure below. Take Qin = 2500 L/min.ElementL, m D, mm fo EKlin150750.02 2280850.03 4331201000.025 2Ans: Q₁ = 731 L/min, Q₂ = 790 L/min, Q₂ = 979 L/min*M

Name: 1. Find the flow distribution in the three-parallel pipe system shown
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 1. Find the flow distribution in the three-parallel pipe system shown in figure below. Take Qin = 2500 L/min.ElementL, m D, mm fo EKlin150750.02 2280850.03 4331201000.025 2Ans: Q₁ = 731 L/min, Q₂ = 790 L/min, Q₂ = 979 L/min*M

INTRODUCTION: Because of some reason, head losses enter the picture as water flows through the…

Engineering

Mechanical Engineering

1. Find the flow distribution in the three-parallel pipe system shown in figure below. Take Qix = 2500 L/min. Element L, m D, mm το ΣΚ en 1 50 75 0.02 2 2 80 85 0.03 4 120 100 0.025 2 Ans: Q₁ = 731 L/min, Q₂ = 790 L/min, Q₂ = 979 L/min 3 *

1. Find the flow distribution in the three-parallel pipe system shown in figure below. Take Qix = 2500 L/min. Element L, m D, mm το ΣΚ en 1 50 75 0.02 2 2 80 85 0.03 4 120 100 0.025 2 Ans: Q₁ = 731 L/min, Q₂ = 790 L/min, Q₂ = 979 L/min 3 *

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Derive an expression for the shear stress acting on the top plate Tw. Q' is the flow rate per unit width (i.e. has units of m^2/s). Express Q' in terms of Tw. When the flow rate per unit width is Q'=1.2*(10^-4) m^2/s, the gap between the plates is 5mm, he device estimates the shear stress at the top wall to be -0.05 Pa. Estimate the viscosity of the fluid. When the tests are repeated for blood ample, different estimates of viscosity are found for different flowrates. What does this tell you about the viscosity of the flow? Use appropriate terminology. As the pressure gradient is increased, at a certain point the measurements cease to be reliable. Using knowledge of fluid mechanics, give a possible reasonfor this. Use appropriate terminology.
An infinitely long cylindrical container has a cross section area of radius R, and is placed horizontally with gravity being in the −y direction, as shown in the figure. The cylinder is 50% filled with water (the shaded part), with density ρ. The other 50% of the volume in the cylinder is filled with air with constant pressure of p = p0. The length of the cylindrical container in the axial direction is W. c) Use control volume analysis and divergence theorem on the 4th quadrant water volume to compute the hydrostatic force acted on the 4th quadrant of the cylinder wall, as shown by the thickened line in the figure.
Find the initial velocity Final velocity=5 m/s Accelertaion=2 m/s2 time=2-s
Given: diameter of pipe in point 1 = 3.9indiameter of pipe in point 2 = 2.5inspecific gravity of the liquid = 0.79h(ft) = 0.60ftpressure at point 1 = 14.6 psiapressure at point 2 = 49 psiapump and motor efficiency = 66%diameter of pipe in point 4 = 4.5indiameter of pipe in point 5 = 2.3 inZ3 = 35ft With the schematic diagram of a pump, tanks, and piping determine the following:1) The velocity of the liquid at point 2 (ft/s)2) Pump work used by the liquid (Wpump U) (hp)3) Electric motor power in out (kW)4) In figure 3, the shaded (pink) in the U tube is mercury; determine y. specific gravity of mercury 13.75) Mass flow rate
Find the initial velocity Final velocity=5 m/s Accelertaion=2 m/s2 time=3-s
Parvinbhai
In mechanical fluid
Oil (SG = 0.84) is flowing in a pipe under the conditions shown in Figure. Find the pressure at point 2