Q3: Three pipes (A, B and C) are interconnected as shown in figure (3). Determine the flow rate in each pipe. The pipes characteristics are given as follows: Pipe L (m) D (mm) f A 610 152 B 488 102 C 1220 203 0.020 0.032 0.024

Q3: Three pipes (A, B and C) are interconnected as shown in figure (3). Determine the flow rate in each pipe. The pipes characteristics are given as follows: Pipe L (m) D (mm) f A 610 152 B 488 102 C 1220 203 0.020 0.032 0.024

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I want to briefly summarize what he is talking about and what you conclude.. the two graph pls urgent(ventilation system)
I want the same solution, but with the mention of questions data and a detailed mathematical solution. 5-27. Blood flows from the left ventricle (LV) of the heart which has an exit diameter of di = 16 mm, through the stenotic aortic valve of diameter d, = 8 mm, and then into the aorta A having a diameter of dy = 20 mm. If the cardiac output is 4 liters per minute, the heart rate is 90 beats per minute, and each ejection of blood lasts 0.31 s, determine the pressure drop over the valve. Take p, = 1060 kg/m². ds SOLUTION The volume of blood pumped per heartbeat is 4 L/min 90 beat/min 1m = (0.04444 L/beat) 44.44(10“) m²/beat 1000 L Thus, the discharge of blood by LV is + _ 44.44(10*) m²/beat 0.31 s/beat 0.1434( 10-3) m²/s Then, the average velocities of the blood flow from the LV and into the Aorta; Vị and V3, respectively are 0.1434(10³) m²/s = V½ [=(0.008 m)*] V = 0.7131 m/s 0.1434(10-3) m²/s = V,[ #(0.01 m)*] Q = V¼A¡; %3D %3! Q = V3A;: %3D V3 = 0.4564 m/s %3D Writing Bernoulli's…
Three pipes A, B, and C are interconnected as shown in figure 1. The pipe dimensions are as follows: Pipeline D(cm) L (m) ƒA 15 300 0.01B 10 240 0.01C 20 600 0.005 Find the pressure at P?
An infinitely long cylindrical container has a cross section area of radius R, and is placed horizontally with gravity being in the −y direction, as shown in the figure. The cylinder is 50% filled with water (the shaded part), with density ρ. The other 50% of the volume in the cylinder is filled with air with constant pressure of p = p0. The length of the cylindrical container in the axial direction is W. c) Use control volume analysis and divergence theorem on the 4th quadrant water volume to compute the hydrostatic force acted on the 4th quadrant of the cylinder wall, as shown by the thickened line in the figure.
10 m 1 m 1 m/s Figure 2 Electricity transmission tower Consider 2D, incompressible, steady flow in a vertical channel at a Reynolds number of 100. This channel flow is shown schematically in the figure below. The figure is not drawn to scale. NEGLECT GRAVITY for the sake of simplicity. Channel length 1 and width w are 10 m and 1 m, respectively, as shown in the figure. Assume thickness= 1 m in the z-direction. The velocity is constant at the inlet, in the y-direction and equal to 1 m/s. The Reynolds number is defined as Re . pvw fl where v is the average velocity at any cross-section. Take p = 1 kg/m3 and adjust μ to get the desired Reynolds number. The absolute pressure at the outlet is 1 atm. Note that the cross-section is a square of 1m by 1m. Contrast this to the laminar pipe flow considered earlier where the cross-section was circular. When the cross-section is square or rectangular, this type of a flow is referred to as a channel flow. When the cross-section is circular, the…
Water flows through pipe A whose diameter is 30 cm and into parallel pipes 1, 2 and 3 and out through Pipe B (diameter= 30 cm). The properties of the pipe are as follows: for pipe 1, L= 300 m, diameter = 10 cm f= 0.020; for pipe 2 L= 240 m diameter= 15 cm f= 0.018 and for pipe 3, L= 600 deiameter= 20 cm f= 0.017. The upstram junction has an Elev. 90 m with pressure of 205 kPa; the downstream junction is at Elev. 30 m. If the average velocity in pipe A is 3.0 m/s, find the flow rate in pipe 3. include your free body diagram. a.24.68 L/s b.80.21 L/s c.107.11 L/s d.212.0 L/s
a) Hydraulic systems commonly have a pump that produces a constant flow rate. Assuming the fluid is incompressible, this situation is known as steady flow or continuity flow. Referring to Figure Q3 (c) the fluid flows at a velocity of 3 m/min at point Q1. The diameter at point Q1 is 50 mm and the diameter at point 2 is 40 mm. In applying the continuity equations, determine the flow velocity at point Q2. Further determine the flow rate in g.p.m (gallon per minute), given 1 gallon = 0.00378 m³. Figure Q3 (c)
Needs Complete solution with 100 % accuracy
Flow (m³ /h) 1 1.5 2 2.5 Pressure difference Ap (bar) 0.005 0.012 0.021 0.034 Kinematic viscosity 10-6 m?/s V (Rough Pipe Radius = 25mm) (Rough Pipe length =L=80cm) Question: An experiment is made using different flow rates in a pipe and pressure differences are given according to the given flow values. According to these; 1. Calculate the pipe roughness height ( e ). 2. Calculate the Reynolds value. 3. Calculate the coefficient of friction f from the Darcy-Weisbach equation. 4. Briefly describe the equations you use and the reasons for using them.
O₂A=80mm AB=70mm 04B=100mm W₂= 1 rad/s a₂= 1 rad/s². 0₂ α 2 60⁰ 3 A B 3 120mm 4 Y 04 ¹50mm Solve for required parameters using the figure above. The figure is not in scale, redraw if possible and applicable. Show pertinent solutions For Velocity: VA, VB, w3 and w