Consider flow of water (μ = 0.001 Pa-s) in the 6-cm diameter cast-iron (ε = 0.26 mm) pipeshown in the figure. What is the discharge in the pipe?a.70.2 lpsd = 6 cmb.10.9 lpsㅗc.40.5 lpsFd.100.2 lps10 mP₁ = 250,000 PaP₁ = 350,000 PaConsider the EGL and HGL of the 200-m pipeline shown. There is a turbine at CD and thefluid is water. Neglect minor losses. What is the velocity in pipe BC?258.482 mEGL252.646 m235.138 ma.29.72 m/sb.5.84 m/sc.10.70 m/s160.085 md.45.03 m/sAHGLL = 100 m229.302 m190.106 mB115.053 m75.053 mf = 0.0140°120.085 mCDf = 0.0145.032 m0 mE

As per our guidelines we are supposed to answer only one question. Kindly repost other questions as…

Consider flow of water (μ = 0.001 Pa-s) in the 6-cm diameter cast-iron (ε = 0.26 mm) pipe shown in the figure. What is the discharge in the pipe? a.70.2 lps b.10.9 lps d = 6 cm c.40.5 lps d.100.2 lps -10 m P₂= 250,000 Pa 40° P₁ = 350,000 Pa

Consider flow of water (μ = 0.001 Pa-s) in the 6-cm diameter cast-iron (ε = 0.26 mm) pipe shown in the figure. What is the discharge in the pipe? a.70.2 lps b.10.9 lps d = 6 cm c.40.5 lps d.100.2 lps -10 m P₂= 250,000 Pa 40° P₁ = 350,000 Pa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please answer everything
FOR THE PIPE NETWORKS SHOWN, THE FLOW OF WATER FROM A TO THE FIRST JUNCTION IS 2 CUBIC FEET PER SECOND. ASSUMIN ALL PIPES HAVE A FRICTION FACTOR OF 0.020 A. DETERMINE THE HEAD LOSS IN FEET IN PIPE 1(ROUND OFF FINAL ANSWER TO TWO DECIMAL PLACES) B. B. DETERMINE THE HEAD LOSS IN PIPE 5 ROUND OFF FINAL ANSWER TO TWO DECIMAL PLACES)
Solve it correctly please. I will rate accordingly
Q3: Three pipes (A, B and C) are interconnected as shown in figure (3). Determine the flow rate in each pipe. The pipes characteristics are given as follows: Pipe L (m) D (mm) f 610 0.020 488 0.032 1220 0.024 A B C Water Figure (3) EL=7om R 152 102 203 B с EL. 15m
Example: What is the pressure at the center of the pipe B?
What are the flow Q and the velocity V when total head loss is H = 25 m?
Q5: For the system shown in figure. Find the total head loss from (A) to (B). the pipe characteristics are as follows: (Take the flow rate equals 0.6m³/sec) and (u = 10-6 m²/sec). %3D Pipe 1 L(m) 900 D(mm) 600 e or for CH.w. e 0.25mm 300 f 0.03 f = 0.02 CHW. 130 2 1500 3 1000 400 4 1500 750 Flow A
The system of pipes shown in figure 3 below has different pipes diameters, lengths, and materials. Suppose the flow enters the system. Evaluate the total losses on the pipe. List your assumptions, if any. DA= 5) сm L1= + 10) m DB= Dc= Dp= D,= 3) сm L2 =L4= Ls = . 7) m Dr= - 8) cm L3= L6 = 5) m V= . 5) m/s L,= - 20) m KĻi: Globe valve, fully open Material A: Cast iron KĻ2 = KL3 =KĻ4 =KL5 Material B-E: Copper KL6: 90° Smooth flanged bend Material B-F: Stainless steel KL7: Sudden expansion KLs: pipe exit E Ls KL6 KL5 L6 D L4 KL7 L3 KL3 L7 C KLA F Globe Valve: B L: fully open A LI K2 Figure 3
1. To model power production in a traditional hydroelectricity unit, we can use the below schematic figure. Water (e= 998 kg/m3, µ = 0.001 kg/m.s) flows from a large tank at elevation 60 m through a cast iron pipe with total length of L diameter 0.1 m. There are three losses associated with sharp-edge entrance, 90° reg- ular elbow and an open globe valve. Outlet of the valve is discharged to atmosphere. The velocity of the water in the pipe is 3 m/s. For minor losses use values for a flanged pipe with diameter of 4". Find the power produced in the turbine in kW 100 m and unit. Hint: If we write energy grade equation between point 1 (surface of water in tank) and point 2 (left hand side of the valve);" P V P V + 21 – hturbine - Ahtot 2g + 2 pg pg 2g where, P = P2 = Patm and Vi 0 (large tank) Sharp-odge entrance 60 m Elbow Turbine Ginhe Valhe
In mechanical fluid
62.4¹,Mw lb Water (Yw ft³ an average velocity of 5 ft/s. Find the change in pressure over 39 ft of pipe. Provide your answer in = D 23.6 x 10-6 ) flows through the 4-in. diameter pipe below with -6 lb-s ft² lb ft² The pipe has roughness of 2x10-4ft. L
Water flows into the tank (Figure 1) at V = 8.5 m/s. Figure 1.5 m 1.5 m 40 mm Al 40 mm BI com 80 mm V < 1 of 1 Part A Determine the velocity of the flow out of the pipe at A. Express your answer to three significant figures and include the appropriate units. μÄ VA= 3.659 Part B 6 Submit Previous Answers Request Answer HA + VB = 30.341 m X Incorrect; Try Again; 2 attempts remaining S 3 Determine the velocity of the flow out of the pipe at B. Express your answer to three significant figures and include the appropriate units. m ? S [www] ? Submit Previous Answers Request Answer X Incorrect; Try Again; 2 attempts remaining