Please solve on a paper, with all FBD included 1.Compute all reactions for the beam if support C moves up a distance of 320/EIwith the load applied. Assume that EI is constant. Note: Take Cy as the redundant force.P = 16 kipsAB6'-6'-12'-CTt

Answered: Image /qna-images/answer/ce80d893-68fa-46cb-bf5f-c04bc8f7e9f2.jpg

Answered: 1. Compute all reactions for the beam…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. Compute all reactions for the beam if support C moves up a distance of 320/EI with the load applied. Assume that EI is constant. Note: Take Cy as the redundant force. P = 16 kips A B 6'- 6'- 12'- C Tt
The simply supported beam is subjected to the force F-550 N and the uniform distributed load with intensity w = 120 N/m. Draw the shear force and bending moment diagrams (in your homework documentation) and determine the equations for V(x) and M(x). Take z = 0 at point A. ру F Vc A wwwm k a b с 5.80 m 3.48 m 3.19 m Support Reactions The reaction at A is The reaction at Dis W a V(x)= In section BC: V(x)= In section CD: V(x)= Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value B N. N. Shear Force and Bending Moment Equations In section AB: N and M(x)= N and M(x)= b N and M(x)= 2013 Michael Swanbom 030 BY NO SA N-m. N-m. x N-m.
An 85pound force is applied to the bent plate as shown. a. Take the moment about the center point between A and B. b. Change the moment into a force couple that acts through A and B.
The simple beam AB shown in the figure is subjected to a concentrated load P and a clockwise couple M₁ = M₁ = PL @ (Use the deformation sign convention. When entering expressions, use the following as necessary: P and L.) acting at the third points. V(x) Vmax
Solve it please and give the solution
Determine the deflection at point C. The reaction at the roller support is 1.6 w0L
1.3-4 Segments AB and BCD of beam ABCD are pin connected at x = 4 m. The beam is supported by a sliding support at A and roller supports at C and D (see figure). A triangularly distributed load with peak intensity of 80 N/m acts on BC. A concentrated moment is applied at joint D. (a) Find reactions at supports A, C, and D. (b) Find internal stress resultants N, V, and M at x = 5 m. (c) Repeat parts (a) and (b) for the case of the roller support at C replaced by a linear spring of stiff- ness k, 200 kN/m (see figure). 80 N/m 200 N-m at joint D A D 4 m B\ 4 m ; 3 m Pin connection Part (c) PROBLEM 1.3-4
1.3-4 Segments AB and BCD of beam ABCD are pin connected at x = 4 m. The beam is supported by a sliding support at A and roller supports at C and D (see figure). A triangularly distributed load with peak intensity of 80 N/m acts on BC. A concentrated moment is applied at joint D. (a) Find reactions at supports A, C, and D. (b) Find internal stress resultants N, V, and M at X = 5 m. (c) Repeat parts (a) and (b) for the case of the roller support at C replaced by a linear spring of stiff- ness ky = 200 kN/m (see figure). 80 N/m 200 N-m at joint D A 4 m B 4 m 3 m Part (c) Pin connection
A horizontal force of F = {-50i} N is appliedperpendicular to the handle of the pipe wrench. Determinethe moment that this force exerts along the axis OA (z axis)of the pipe assembly. Both the wrench and pipe assembly,OABC, lie in the y-z plane. Suggestion: Use a scalar analysis.
Compute the support reactions of the given beam below. Also, determine the maximum value of the positive and negative shear as well as the moment. Note: pt. a is hinge support, pt. b is roller support, pt. c is internal hinge support, pt. d is internal roller support, pt. e is roller support, and pt. f is a hinge support. Hint: Try to expose the internal reaction/s of the internal hinge support at pt. c as well as for pt. d internal roller support. For the units, the forces are in kN, then for the distances, take it as meters. 30k 5K ... 30k 2 长 roller 24 24
3. Determine the reactions at the supports, then draw the moment diagram. The moment of inertia for each segment is shown in the figure. Assume A and C are rollers and B is a pin. Take E = 200 GPa. 20 kN 20 kN LAB 120(10) mm² [BIBC = 90(106) mm² C |3m|3m|3m| 50 KN 4 m -4 m
Using the force method of analysis, determine the reactions at the supports then draw the shear and moment diagrams for the beam shown in in the diagram Assume the support at B is a roller. Use the moment at A as the redundant. Take ?? as constant

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

1. Compute all reactions for the beam if support C moves up a distance of 320/EI with the load applied. Assume that EI is constant. Note: Take Cy as the redundant force. P = 16 kips A B 6'- 6'- 12'- C Tt