1. A fan that can provide air speeds up to 50 m/s is to be used in a low-speed wind tunnel with atmospheric air at 25°C. If one wishes to use the wind tunnel to study flat-plate boundary layer behavior up to Reynolds numbers of Rex=108, what is the minimum plate length that should be used? At what distance from the leading edge would transition occur if the critical Reynolds number were Rex,c=5×105? Answer: 31.4m 0.157m

1. A fan that can provide air speeds up to 50 m/s is to be used in a low-speed wind tunnel with atmospheric air at 25°C. If one wishes to use the wind tunnel to study flat-plate boundary layer behavior up to Reynolds numbers of Rex=108, what is the minimum plate length that should be used? At what distance from the leading edge would transition occur if the critical Reynolds number were Rex,c=5×105? Answer: 31.4m 0.157m

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.29P: Air at 20C flows at 1 m/s between two parallel flat plates spaced 5 cm apart. Estimate the distance...

See similar textbooks

Similar questions

Air at 1000C flows at an inlet velocity of 2 m/s between two parallel flat plates spaced 1 cm apart. Estimate the distance from the entrance to the point where the boundary layers meet.
Find the related Average Nusselt number equation
Please help me get the correct answer quickly, please. :((
Show every step please not Ai generated im trying to understand what im doing wrong.
Calculate the Reynolds numbers at the root chord location for the following aircraft. Assume that the density and dynamic viscosity of air at sea level are 0.002378 slug/ft’ and 3.737 x 107 slug/(ft•s): (a) A DC-3 with a wing root chord length 15.25 ft flying at 250 ft/s at sea level. (b) An F-22 with a wing root chord length 21.5 ft flying at 920 ft/s at sea level.
Ambient Air has a temperature of 20°C and creates a boundary layer which is beside a solid walI, follows a sinusoidal velocity profile. The boundary layer thickness is around 7mm having a peak velocity of 9 m/s. Solve for the shear stress in a boundary layer at height (y) equal to: a. 0 b. 3.5mm Umax 9 m/s %D c. 7mm µ = 1.85 x 10 -5 Pa•s Peak 7 mm sin Sine Wave U = Umax Sins
(1) Experiments show that in a slightly Viscorur flund at on a молод high speeds the drag force fo exerted on body depends on several parametes. An engineer assumes that the drag force fo is a functon of the budy width normal to the upstream Velocity, I upstream Velouty, ✓, the upstream flud veElucay P viscosity, M, speed of sound, I and the airfoils surface roughnars. " use the Buckingham ♬ Theorem to determine the functional dependence of to on non-dimensional flow similarity parameters (2:) Lot the transition to turbulence occur when I = 1.01m, V= 1·01m/s and M₁P = 1:01·10⁰5 m² s. Calculate the transchen Reynolds number, Retrains.
2. Experiments have shown that, for airflow at T=35°C and V1= 100 m/s, the rate of heat transfer from a turbine blade of characteristic length L₁ = 0.15 m and surface temperature Ts,1=300°C is q1=1500 W. What would be the heat transfer rate from a second turbine blade of characteristic length L2 = 0.3 m operating at Ts,2=400°C in airflow of Tx-35°C and V2 = 50 m/s? The surface area of the blade may be assumed to be directly proportional to its characteristic length. Answer: 2066W
Please write down a related Average Nusselt number equation for each case. (Do not calculate) Laminar flow SCHEMATIC: Air 4∞ = 2 m/s Top = 25°C p = 1 atm w= 0.2 m L=25 AL 0.25 m T = 500 °C ASSUMPTIONS: (1) Top surface is smooth, (2) Bottom surface is adiabatic, (3) Critical Reynolds number is 5 × 105, (4) Negligible radiation.
Q4-Q6: A device is used to cool hot copper spheres of diameter 5 mm from an average temperature of 200C to 50C by letting them fall in air at 25°C and latm. Use drag coefficient C, = 0.4 and Whitaker correlation in your calculations. Assume the spheres fall at their terminal velocities during the process. Q4 improve the accuracy? Iteration is not required. ) Determine the terminal velocity of a sphere. Is the use of C, = 0.4 appropriate? If not, how to
I need correctly
Ambient Air has a temperature of 20°C and creates a boundary layer which is beside a solid wall, follows a sinusoidal velocity profile. The boundary layer thickness is around 7mm having a peak velocity of 9 m/s. Solve for the shear stress in a boundary layer at height (y) equal to: a. 0 b. 3.5mm Umax = 9 m/s c. 7mm µ = 1.85 x 10 -5 Pa•s Peak 7 mm y Sine Wave U = Umax sin