01 [101 Rigid bar ABC (see figure) is supported by axial bar BD and a pin connection at C. A load P-6000 N is applied at A. Member BD is a 20 mm wide by 9 mm thick rectangular cross-section bar. The pin at C has an allowable shear stress of tallowable - overall dimensions of the assembly are a =110 mm, b= 190 mm, c=50 mm and d= 13- mm. (a) Determine the normal stress in member BD. (b) Determine the required pin diameter at C. 115 MPa. The %3D B. D.

01 [101 Rigid bar ABC (see figure) is supported by axial bar BD and a pin connection at C. A load P-6000 N is applied at A. Member BD is a 20 mm wide by 9 mm thick rectangular cross-section bar. The pin at C has an allowable shear stress of tallowable - overall dimensions of the assembly are a =110 mm, b= 190 mm, c=50 mm and d= 13- mm. (a) Determine the normal stress in member BD. (b) Determine the required pin diameter at C. 115 MPa. The %3D B. D.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QI A rigid bar ABCD is pinned at end A and supported by two cables of equal length at points B and C.The cable at B has nominal diameter D=12 mm and the cable at C has nominal diameter D= 20 mm. IF a load P=30 -dc KN acts at end D of the bar. What is the stresses for the cables at B and C if the temperature rises by 60°C. (E = 140 GPa and a=12 x 10/°C for both cables). -26 to -26- P
Gg
Solve the problem stated below. Use bond papers and black ball pen. Make your solution clear and clean. Draw the FBD. PROBLEM Figure: A homogeneous bar AC with negligible mass is supported by a pin at A and cable cable BC, which carries a load of 20 kN as shown in the figure. a) Determine the force reaction at A, (PA). b) If the shearing stress is 80 MPa (double shear), determine the pin diameter at A. 5 m. 3 m pin 4 m double shear 60° 20 kN
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. The diameter of aluminum rod (1) is 2.50 in., the diameter of brass rod (2) is 1.75 in., and the diameter of steel rod (3) is 3.00 in. Determine the axial normal stress in each of the three rods. Assume P = 5 kips, Q = 3 kips, R = 13 kips and 5 = 24 kips. The normal stress is positive if tensile and negative if compressive. σ₁ = Answers: 0₂ = (1) 03 = (2) i i A Q B C D ksi ksi ksi
6
A steel column of hollow circular cross section shown in Figure is supported on a circular steel base plate and concrete pedestal The column has outside diameter 220 mm and a wall thickness of 15 mm. It supports an axial load of 680 kN.a. Determine the bearing stress induced by the column to the base plate in MPa.b. If the allowable bearing stress on the pedestal is 10MPa, determine the required diameter of the base plate in mm.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. One load of P=33P=33 kipskips is applied to the assembly at A, two loads of Q=30Q=30 kipskips are applied at B, and two loads of R=35R=35 kipskips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 1717 ksiksi. The normal stress magnitude in steel rod (2) must be limited to 3030 ksiksi. The normal stress magnitude in brass rod (3) must be limited to 2121 ksiksi. Determine the minimum diameter required for each of the three rods.
A simple pin-connected truss is loaded and supported as shown in the figure. All members of the truss are aluminum pipes that have an outside diameter of 3.00 in. and a wall thickness of 0.210 in. Determine the normal stress in truss member BC. Assume P = 4 kips, Q = 2 kips, a = 5 ft, b = 9 ft, and c = 7 ft. The stresses are positive if tensile and negative if compressive. Answer in ksi rounded-off to 2 decimal places. P e (3) B b T Gra a Adc Ref you
A homogenous bar AC with negligible mass is supported by a pin at A and cable BC, carried a load of 20 kN as shown in the figure. Determine the pin diameter at A if the allowable shearing stress is 80 MPa. (double shear) 3 m. 4 m. C 20 kN B.
Uniform AB brass rod has a rectangular vertical cross section, fixed with support and pin as shown in the figure. Both ends of the rod are free in the vertical direction but rotation in the horizontal direction is prevented. a) Find the b / d ratios at the safe boundaries for the horizontal and vertical axes?b) What would be the safety factor if P = 1.8 kN, L = 7m, d = 60mm and E = 150GPa?
Aluminum tube AB is fixed on support A, and the load P=60 KN is applied on Steel rod BC that is welded to tube AB via plate B. The cross-section area of the tube is equal to 1100 mm2 and the diameter of the rod is equal to 15 mm. calculate the axial deformation of point C? (Esteel=200GPa and EAl=70GPa)