B A homogenous bar AC with negligible mass is supported by a pin at A and cable BC, carried a load of 20 KN as shown in the figure. Determine the pin diameter at A if the allowable shearing stress is 80 MPa. (double shear) 3 m. A 4 m. 20 kN

B A homogenous bar AC with negligible mass is supported by a pin at A and cable BC, carried a load of 20 KN as shown in the figure. Determine the pin diameter at A if the allowable shearing stress is 80 MPa. (double shear) 3 m. A 4 m. 20 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q8(): For the truss shown in the Figure, if the diameter of pins at A and G are 3 in and2 in, respectively. Both stresses in A and 70 kips 50 kips A 4ft В 4# C 4ft are double shear. Determine the shear stresses in 9 ft pins at A and G and the stresses members AG; AF member GF if their diameter is 4 in and in.
Solve the problem stated below. Use bond papers and black ball pen. Make your solution clear and clean. Draw the FBD. PROBLEM Figure: A homogeneous bar AC with negligible mass is supported by a pin at A and cable cable BC, which carries a load of 20 kN as shown in the figure. a) Determine the force reaction at A, (PA). b) If the shearing stress is 80 MPa (double shear), determine the pin diameter at A. 5 m. 3 m pin 4 m double shear 60° 20 kN
2. Refer to the figure below. In addition to the load at point D, if another load Q (Q=10F) along x direction acts at the center of the right end section of bar OABC, solve for the maximum load F with a safety factor of 2.0 using the maximum shear stress theory. Find the stresses at the origin point O. Assume the yield strength of the steel is 42 kpsi with v=0.3. Hints: The centroid of a semicircle lies at a distance of 4r/(3) measured along the vertical radius (r) or y-direction. 2 in. 1-in D. -in R. 1-in D. 12 in 15 in 1-in D.
6
The shaft shown the figure below, is supported by a bearing on the left end. The shaft also supports a pulley on the right end, which rotates. The tensions in the belt of the pulley are F. =2,739 y and F,=1,362 N. Also, a completely reversed axial load of F 11 N is applied to the right end. The shaft is made of UNS G10450 CD steel, with 2. a ground surface and 99 z reliability and operates at room temperature. Assume, K =1.35 for torque and formula 6- 34 to calculate K fs' K, - 1 K = 1 + (6-34) 1+ va/ Vr Bending or axial: Va = 0.246 – 3.08(10)S+ 1.51(10-)S, – 2.67(10-*)S 50 s Su s 250 kpsi Va = 1.24 - 2.25(10-)S+1.60(10)$ – 4.11(10-1)S, 340 S S 1700 MPa (6-35) Torsion: Va = 0.190 – 2.51(10-)S+ 1.35(10-), – 2.67(10-)S 50 < Su < 220 kpsi Va = 0.958 – 1.83(10-)S+ 1.43(10-")S-4.11(10-1)s 340 < S S 1500 MPa (6-36) All fillet radius r-0.1d All dimensions are in mm 300D -30 100 :600 1. Identify the critical point(s) on the shaft and show it clearly on the diagram. 2. Draw the cartesian…
Q8(): For the truss shown in the Figure, if the diameter of pins at A and G are 3 in and 2 in, respectively. Both stresses in A and 70 kips 50 kips 4 ft B 4 ft are double shear. Determine the shear stresses in pins at A and G and the stresses in 9 ft members AG; AF member GF if their diameter is 4 and in.
A homogenous bar AC with negligible mass is supported by a pin at A and cable BC, carried a load of 20 kN as shown in the figure. Determine the pin dieameter at A if the allowble shearing stress is 80 MPa. (double shear)
In the figure, member AB is used to support a load of 20kN at the free end, if the cable CD has adiameter of 25mm, what is the tensile stress in the cable?
5
Calculate the average shear stress in MPa of the pins Band C on the frame shown in the figure. Note that thesepins are subjected to double shear and have a diameterof 0.5 inch.