how many times is the system

Q: 1. A wall-mounted jib crane is shown in the Figure below. Overall dimensions of the crane are a =…

A:

Q: In the figure below, a pulley can pull a 1-ton load from rest to 3 m/s upwards at 2 seconds. AB and…

A: Given: The load, W = 1 ton The speed, v = 3 m/s The time, t = 2 s The compressive stress, σ = 140…

Q: Link 2, shown in the figure, is 25 mm wide and 11 mm thick. It is made from low-carbon steel with…

A: Wide W = 25 mm Thickness t = 11 mm Sy = 165 MPaForce F = 80 KNFor  low-carbon steel E = 207GPa

Q: The load in the figure below is attached to the wall with a ball joint at point A. Calculate the…

A:

Q: The figure shows a cantilever of length L = 4 m consisting of steel angles size of 100 x 100 x 12 mm…

A:

Q: AB, BC, BD ropes made of material with elasticity value in Table 2 are in balance as shown in the…

A: Given Data: θ=90° β=120° α=150° FAB=40000 N Areas: AAB=200 mm2 ABC=173 mm2 ABD=100 mm2 Lengths:…

Q: The figure (not drawn to scale) shows a metallic cylindrical column submitted to a combined load:…

A:

Q: 4-3.18. Repeat Prob. 4-3.17 if the loads Q are zero and each load P = 2000 lb.

A:

Q: The pulleys in the system are under the influence of the forces shown in the figure. The yield…

A:

Q: Link 3 shown acts as a brace to support the 270-lb load. For buckling in the plane of the figure,…

A:

Q: Q2- The steel bar shown in the figure is subjected to a reversed axial load fluctuating between 28…

A:

Q: Urgent

A: Given:-

Q: The A-36 steel rod BC as shown in Figure Q3 has a diameter of 54 mm  and is used as a strut to…

A: For solution refer below images.

Q: Problem 3. The tension lock shown at the figure below will be loaded by an axial force F = 10 kN.…

A:

Q: Solve the problem

A: Step 1: Step 2: Step 3: Step 4:

Q: The rigid arm of negligible weight shown in the figure supports a load of F = 852 N. The chains are…

A: Given data: F=852 Nx1=5 mx2=4 my=7 mz=5 m Need to determine the Magnitude of the force in FBE.

Q: The end plates of a high pressure boiler accumulator are fixed using a number of bolts of M16 × 2-…

A: Any action that can change the state of motion is called force. Force is described by its magnitude,…

Q: Q10/ Find the equivalent stiffness for the systems shown in figures below. K1 = 300 N/m Ks = 400 N/m…

A: First three parts will be done from multiple part questions. Please post again for other parts…

Q: (b) V brakes Question Four A long retaining wall is braced by wood shores set at an angle of 30° and…

A:

Q: high pressure boiler accumulator are fixed using a number of bolts of M16 × 2- C, grade 5.8, with…

A:

Q: how many times is the system safe

A: For solution refer below images.

Q: The steel bar in the figure has a hollow circular cross-section (dais = 111 mm, tooth = 85 mm), one…

A: The expression for the buckling load, one side hinged and one side is shown below.

Q: figure is attached to a shaft with a diameter of d=50mm with a welded seam closed on both sides with…

A: Given:F=8 kNd=50 mm or 0.05 mr=d2=502=25 mm or 0.025 ma=4 mm or 0.004 mτ=180 N/mm2

Q: A rectangular plate of width b-40 mm and thickness s 20 mm has a hole with a diameter d=8 mm in the…

A: Given:b=40 mms=20 mmd=8 mmF=15000 NFor dw=840=0.2;From the graph:Kf=2.5Stress developed without…

Q: 3) The rigid horizontal bar AB is supported by three vertical rods as shown in the figure and…

A:

Q: specification required for the bolt

A: Given; Three bolt system as shown in figure;The bolt material has ,shear yield…

Q: The A frame shown in the figure is attached to an overhead beam by 2 cap screws, each of which can…

A: To determine the appropriate screw for the given load and conditions, we need to follow several…

Q: igit of matrix no is (8) fifth digit of matrix no is (0) so A;8   and B;0

A: P1=65B5N=6505NdAB=30mmtAB=1Amm=18mmdBC=50mmtBC=9mmA=8B=0 To-Find:- a) σAB Normal-stress=?b) P2=?c)…

Q: Q2- The steel bar shown in the figure is subjected to a reversed axial load fluctuating between 28…

A:

Q: Consider the frame shown in Fig 4. A 100N load is suspended around a fixed drum with radius 2 m…

A: Draw the free-body diagram of the frame.

Q: As seen in the figure, the block on an inclined plane is lifting from 0 0 with two degrees increment…

A:

Q: load of F=1433 kgf will be hung on a Workshop crane as in the figure. The pole to be used has a…

A:

Q: This is a multi-part question. Once an answer is submitted, L- P

A: Given-Information:- Length, L = 4 m Angle size 100×100×12 mmP =3000 N a =1.75 m =1750 mmW =1000 N/m…