Link 2, shown in the figure, is 25 mm wide and 11 mm thick. It is made from low-carbon steel with Sy= 165 MPa. The pin joints are constructed with sufficient size and fit to provide good resistance to out-of-plane bending. Use Table 4-2 shown below for recommended values for C. Determine the following for link 2: a.)Axial Force b.)Yield factor of safety c.) In-plane buckling factor of safety and Out-plane buckling factor of safety

Q: Calculate the minor axis (z-z) axial flexural buckling capacity of a 152×152×30UC S275 assuming an…

A: Whenever underlying individuals are exposed to compressive powers , the individuals might fall…

Q: Problem 8-53: The coiled spring is subjected to a force P. If we assume the shear stress caused by…

A: Given Data:A coiled spring is subjected to a force P.The shear stress caused by this force on any…

Q: The figure Q3 below shows a bolt holding together two components. The bolt has a load bearing…

A: Thickness of component 1, t1 = 5 mm Thickness of component 2, t2 = 10 mm Modulus of elasticity of…

Q: The five-bolt connection must support an applied load of P= 196 kips. If the average shear stress in…

A:

Q: 15 in 05 im 24 in The machine link shown is subjected to an axial load P, as shown. The link is…

A:

Q: 600 N Problem 5: Fatigue A bicycle crank experiences cyclic loading due to the force applied by the…

A:

Q: A course pitch metric grade 9.8 bolt with a hexagonal nut assembly is used to keep two machined…

A: Step 1: Step 2: Step 3: Step 4:

Q: The end plates of a high pressure boiler accumulator are fixed using a number of bolts of M16 × 2-…

A: Any action that can change the state of motion is called force. Force is described by its magnitude,…

Q: Problem 1: In the figure below a solid bar with a 1.00 in diameter is subjected to a bending moment…

A: Given data, Diameter of the solid bar, d = 1 in Twisting moment and bending moment are equal, i.e.,…

Q: The figure shows a connection that employs three SAE grade 4 bolts. The tensile shear load on the…

A: From Table 8-9: for SAE Grade 4 boltsFrom Table A-20: for AISI 1020 HR

Q: A butt connection is shown in the following figure. Plates is Q235 steel; 8.8 Grade M16 high-…

A: Load bearing capacity  Loadbearing capacity is the maximum ability of a structural member or…

Q: The bracket shown in the figure is bolted a ceiling beam to support a fluctuating vertical load…

A: Given kb = 8 Mlb/in km = 18 Mlb/in Bolt Size = 5/8 in Fatigue design factor = 2.5 To find Repeated…

Q: 10) A screw clamp similar to the one shown in the figure has a handle with diameter in made of…

A: Given Screw clamp To find Torque it can handle

Q: The metallic hollow pipe shown in Figure Q1 is fixed at both its ends, and is under axial…

A:

Q: The cantilevered handle in the figure is made from mild steel that has been welded at the joints.…

A: Given: To find: Vertical deflection at the tip

Q: Solve for a and b and c

A:

Q: 1) Ball bearings support the rotating axle shown below at points A and D. The rotating axle is…

A: Treat the shaft as simply supported beam with supports at A and D.Here  are reaction forces at…

Q: Calculate the maximum tensile stress developed in a 1/4-20 bolt (Major dia = 0.2500" and Root dia =…

A: Write the given data with suitable variables: P=426 lbdmin=0.1959 in

Q: A solid 4340 HR Steel tie rod of length Lrod = 850 mm is employed to compress a 6061-T6 aluminum…

A: 4340 HR steel rod.Diameter of the rod, drod= 22.5 mmLength of the rod, Lrod= 850 mm6061-T6…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.