Q3) A short stepped bar is shown in rigure below. The stiffness of the large section is 12 kN/mm and the stiffness of the small section is 8 kN/mm. End 1 is fixed and an axial load of 6 kN acts at node 3. Determine the displacements at node 2 and node 3. AN imm AN im Figure (1)

Q3) A short stepped bar is shown in rigure below. The stiffness of the large section is 12 kN/mm and the stiffness of the small section is 8 kN/mm. End 1 is fixed and an axial load of 6 kN acts at node 3. Determine the displacements at node 2 and node 3. AN imm AN im Figure (1)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A flat bar with a hole (see figure) has widths b = 60 mm and c = 40 mm. The fillets have radii equal to 5 mm. What is the diameter dmax of the largest hole that can be drilled through the bar without reducing the load carrying capacity?
Q1 (а) A hollow circular post ABC as shown in Figure Q1 (a) supports a load P, = 65B5 N acting at the top. P2 is applied around the cap plate at B. The outer diameters and thicknesses of the upper and lower parts of the post are dAB = 30 mm, tu =1A mm, dzc = 50 mm, and t3c =9 mm , respectively. A=1 B=0 (i) Calculate the normal stress o AR on the upper part of the post. (ii) If it is desired that the lower part of the post have the same compressive stress as the upper part, what should be the magnitude of the load P,? (111) If Pi remains at 65B5 N and P2 is now set at 10050 N, what is the new thickness of BC that will result in the same compressive stress in both parts?
A round bar is loaded in both torsion and bending with rd=0.15 and Dd=1.5 with the geometry shown on the left. Your boss has proposed changing the design to the geometry on the right to make the bar stronger and stiffer. Determine if this is a good idea. Assume r, D, dwould all remain the same. 1. Amard tarisdetisboth oan and bongwth te=015 a Ata 1.5 wn the prinetry sow on the let Vur oeshas egronery on the ghe1o moke me bor aronger and se. Derermine i isa geod idea AameAer. D, dwld a ronair Te same
Find the forces in CE and DE of the truss shown in Figure (6) below (indicate tension or compression). Assume all joints are pinned. "tan (2+5) = 56.3² H pe 0.67 B 1m 1m C 1KN 1m 1m 1m F Figure (6) FDE = 0.4 kN (C) & FCE = 0.67 kN (T) 10% bis -75 0.75m G PNG 6-3-1+NG 3 NG= mbination of the method of joints
Gkuestrons T ØD VP The figure (not drawn to scale) shows a metallic cylindrical column submitted to a combined load: bending and torsion. The column contains an hemispherical groove of radius r, located at a distance L from the point of application of the loads. You are given the column diameter D = 68 mm, the groove radius r = 6 mm, the distance L= 200 mm, the bending load P=5 kN, and the torque T = 600 N.m. The material data are Young's modulus E = 122 GPa Shear Modulus G = 55 GPa Poisson's ratio v= 0.1 and Yield strength oy = 380 MPa. a) Write a numbered list of the calculation steps required to obtain the factor of safety in yielding based on the maximum distortion energy (Von Mises) criterion.
Calculate the maximum load (P) that can be supported by the knuckle joint that shown in the figure below. The joint material has the following allowable stresses: tensile stress = compressive stress -50 Mpa, shear stress =35 Mpa and crushing stress = 90 Mpa. (Assuming: the load is applied statically). P- C1 78 mm C1 78 mm C2 C3 C3 156 mm 98 mm C4 C1 C5 C1 60 mm C4 C5 P. C5 C2
Uniform AB brass rod has a rectangular vertical cross section, fixed with support and pin as shown in the figure. Both ends of the rod are free in the vertical direction but rotation in the horizontal direction is prevented. a) Find the b / d ratios at the safe boundaries for the horizontal and vertical axes?b) What would be the safety factor if P = 1.8 kN, L = 7m, d = 60mm and E = 150GPa?
2. A 2-in.-diameter steel tube with a wall thickness of 0.05 inch just fits in a rigid hole. Find the tangential stress if an axial compressive load of 3140 lb is applied. Assume v=0.30 and neglect the possibility of buckling. data: 2 in Rod Wall Rod Vill
Hi please help me answer this problem and draw free body diagram
A 28 mm diameter rod with a 30 mm diameter handle as shown in Figure Q1 has two 90 degree bends. The handle is attached to the wall at 'A' while 1.8kN load is applied at the end of the rod at 'E'. Calculate Maximum Shear Stress at location 'A' and 'B' and determine it critical location. Bending load at point 'A'? Bending load at point 'B'? (Nm) Torsion load at rod; 'T'? Normal Stress due to bending load at point 'A'? (MPashear Stress due to torsion load at point 'A'? (MPa) 1st Principle stress at point 'A' (max principle stress)? (MPa Maximum shear stress at point 'B'? Critical Location? (L1) 170 $30- (L2) в 470 $28- F= 1.8kN| E 300 100 (L3) D Figure Q1