I need the answer as soon as possible The primary and secondary shear loads on bolt PA steel bar of 10 x 50 mm is cantilevered with two M12bolts (Pand Q) to support a static load of 4 kN as shownin the figure.100 400 1001.7 mP.4 kNThe primary and secondary shear loads on boltrespectively, are

Given; A steel bar of; = 10×50 mmCantilevered with two M12 bolts,To support a static load of 4kN…

Answered: he primary and secondary shear loads on…

Engineering

Mechanical Engineering

he primary and secondary shear loads on bolt P

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.6.5P: An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the...

See similar textbooks

Related questions

Q: For the given state of stress. determine the normal and shearing stresses exerted on the oblique…

A: The result and conclusion are attached here in next few steps:

Q: Attemperator increases the higher heat absorption at high loads to ensure that the desired steam…

A: The given statement is true.

Q: An airplane is making a level turn at 200 knots while pulling 2.5 g's (n = 2.5). Calculate the turn…

Q: Heat transfer by convection واجب سي (1 )Example S Air at 2 atm and 200 c°is heated as it flow…

A: To find: The heat transfer per unit length of tube and the amount of bulk temperature increases.…

Q: Consider the diagram of a block attached to a wall being supported by a pole. Find the net moment…

Q: 8- A coper road is inserted into a hollow aluminum cylinder . The copper rod projects 0.130 mm as…

Q: Bearings are manufactured to take loads of type: Select one: a. Pure radial loads b. A combination…

A: It is required to give correct answer

Q: Q3. The lamp has a weight 40 N) and is supported by the siX cords connected together as shown.…

Q: The mass of a turbine rotor of a ship is 8 tonnes and has a radius of gyration 0.6 m. It rotates at…

Q: rectangular section the ratio of maximum shear stress to the average shear For a stress is

A: Given data : Rectangular section Width=B Depth=D Shear force=V Average shear stress=ζAvg Maximum…

Q: Determine the cycle efficiency.

Q: Q3/ A beam supports a distributed load as shown. 1- Explain the beam type 2- Draw F.B.D 3- Determine…

A: (1) Since the beam is free at one end and fixed at other end, the beam is a cantilever beam.

Q: •A power station will run 24 hours a day with 7 operators working 8 hours per day and 5 days in a…

A: Given: To find the annual cost

Q: sleeve is 6 poise . The shaft is of diameter 0.5 m and rotates at 210 Prob. 6: The dynamic viscosity…

A: There are two main types of bearings, namely, rolling contact bearing and sliding contact bearing.…

Q: The figure below shows a simply supported beam with an overbang. The beam is made of two types of…

A: σpi=11 mPa Epi=8 GPaσpl=14 mPa Epl=12 GPaFind allowable magnitude w=?

Q: A force of magnitude P = 180 N is applied stationary machine handle as shown. Wr. force and moment…

A: the component parallel to the x axis will create a reaction along the negative x axis component…

Q: {2)What is the maximum gauge pressure of water th OWhat is the maximum gauge pressure of water th.…

A: Given Data : Height (h)=2.5 m

Q: Superheated steam originally at P, and T, expands through a nozzle to an exhaust pressure P.…

A: Given:

Q: 3- A Compound bar composed of three bar as shown .Determine the stress if the temperature change…

A: Calculated stress in brass and aluminum block when it compounded.

Q: A 150 mm diameter orange (P =950 kg/m.K, c= 4150 J/kg.K and k= 0.6 W/m.K), aproximately spherical in…

Q: Problem 10.2. A stepped steel shaft with diameters d, = 56 mm and d = 52 mm is twisted by torques T1…

A: d1 = 56 mm d2 = 52 mm T1 = 2.5 kN.m T2 = 1.5 kN.m

Q: learly explain your understandings why a couple cannot produces ny translatory motion (i.e., motion…

Q: 1- A Carnot cycle works on steam between the pressure limits of 7 MPa and 7 kPa. Determine thermal…

Q: Determine the force in members BC, CF, and FE. State if the members are in tehsioH OF 2 m 10 kN 25…

Q: Ratio of soldification time of a cylindrical casting (Height=radius) of that of a cubic casting of…

Q: In the figure shown, what the minimum height (h) t which water must rise in th water tank in order…

Q: (B)Fig.I shows oil of viscosity (0.09 N.s/m*) filled annular space of a cylinder of (11.05 cm)…

A: Given:μ=0.09 N.s/mD=11.05 cm =0.1105 md=11 cm =0.11 mF=20 NL=13 cm =0.13 m

Q: An aeroplane makes a complete half circle of 50 metres radius, towards left, when flying at 200 km…

A: given:Speed, v=200 kmph or 55.56 m/smass, m=400 kgradius of gyration, k=300 mm or 0.3 mEngine speed,…

Q: irough the impeller is con pack at angle of 46° to the et of pump.

Q: cylinder havi th oil of densit axis at an ang

A: we have to find out thrust on bottom of cylinder radius =Rheight=Hangular velocity =ω

Q: 6) Which of the following statement(s) is/are correct? i. The ratio of the test temperature to the…

A: Given Material statement To find The correct statement

Q: Q4) A) What is the difference between R and Ru and how these two are related. B) What is the…

A: 4.) Characteristic Gas Constant (R) :- with help of molar mass of gas and STP values R will be…

Q: In a gas turbine, hot combustion products with the specific heats c,= 0.98 kJ/kgK, and c. = 0.7538…

Question

I need the answer as soon as possible

The primary and secondary shear loads on bolt P
A steel bar of 10 x 50 mm is cantilevered with two M12
bolts (Pand Q) to support a static load of 4 kN as shown
in the figure.
100 400 100
1.7 m
P.
4 kN
The primary and secondary shear loads on bolt
respectively, are

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
Compare the angle of twist 1 for a thin-walled circular tube (see figure) calculated from the approximate theory for thin-walled bars with the angle of twist 2 calculated from the exact theory of torsion for circular bars, Express the ratio 12terms of the non-dimensional ratio ß = r/t. Calculate the ratio of angles of twist for ß = 5, 10, and 20. What conclusion about the accuracy of the approximate theory do you draw from these results?
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
Solve fast Include fbd. Urgent
The last 3 digits of my I.D. number is 237 and the last digit of my I.D number is 7
5
All parts correct and handwritten
Two metal plates, are joined as show below. Using standard material values, complete the following: a. Select a suitable bolt diameter b. For a load P = 150 kN. Determine the minimum plate thicknesses Hex head Aluminium bolt P Brass Upper plate P 150 Linear dimensions in mm 35 + # 80 35 P Copper Lower plate Modified from Statics and Strength of Materials by Morrow and Kokernak
question is on the figure
Calculate each of the following under 20 kN load on a structure given below where all pins have a diameter of 10 mm. a) What is maximum stress on bar BD? b) Check the Pin strength at Location D against shearing. (Use ?Y=300 MPa, n=2 - factor of safety for Pin). Is it secure/safe or not? c) Check the Pin and Bearing strength against shearing at Location C. Are they secure/safe or not? (Use ?Y=300 MPa, n=2 - FOS for pin/bearing and ?Allow=300 MPa for bearing).