The following stress condition is applied to a cubic material. Normal stress in the x direction is 15 Mpa, normal stress in the z direction is -7 Mpa and the shear stress in the x-z plane is 59 Mpa. (a) Write the stress tensor (b) Find the maximum normal stress (c) Find the angle with respect to the x- axis at which the maximum normal stress is applied (d) Find the maximum shear stress (e) Determine the angle with respect to the x-axis at which the maximum shear stress is experienced

Q: The following stress condition is applied to a cubic material. Normal stress in the x direction is…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: A very thick structure is subjected to certain traction boundary conditions on its surface. The…

A: As asked only the first three are solved. φ(x,y)=sinxAx2e-y+Bey

Q: For the three stress states given, find all principal normal stresses using the eigenvalue method.…

A: In eigenvalue approach, the eigenvalue represents the principal normal stresses and eigenvectors…

Q: The strains for an element of material in planestrain (see figure) are as follows:  εx = 480 X 10-6…

A: Given data as per question εx=480×10−6εy=140×10−6γxy=−350×10−6

Q: 1. Given a combination of stresses on an element shown in the figure, (a) draw a Mohr’s circle…

A:

Q: The opening between a 3m long piece of steel and a rigid support is 1.5mm.As the temperature rises…

A: Given : L = 3 m = 3000mm Yield allowance δ = 1.5 mm dT = 25 ⁰ C α = 1.1 x 10-5 /⁰C   NOTE :from…

Q: Tensile test specimens are extracted from the "" and "y" directions of a rolled sheet of metal. "X"…

A: Since you have posted a question having multiple subparts we will solve first three subpart for you.…

Q: ɛ=-100µ 120° 120° ► x ɛ=200µ ɛ=-200µ 3D

A:

Q: Since the suspended mass is m=1500 kg as shown below; Find the force (F) N and the stress N/mm2 in…

A:

Q: For the 2-Dimensional state of stress at a point represented by the following figure: (i) Determine…

A: According to our guidelines, we are supposed to answer the first three sub parts . Please repost the…

Q: [20 [o] = 10 0 b. Plot Mohr's circle for this stress state. 10 01 10 005 0 a. Determine the stress…

A: (a) Write the given stress matrix. σ=2010010100005

Q: A very thick structure is subjected to certain traction boundary conditions on its surface. The…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: A copper wire of length (400+R) cm , diameter of (4+R) mm and mass of (5000 + R) g, if Young's…

A:

Q: For the following structure, represent Mohr's Circle at point K of the structure and point Section…

A: given data; ⇒b1=180mm⇒h1=221m⇒h2=21mm⇒thickness(t)=21mm⇒reaction force (RA)=181.22KN…

Q: On a stress element, the following stresses are acting: σ x = 5 ksi (Compression) σ y =  10 ksi…

A:

Q: In an elastic body system, a point has the following state of stress components, Oxx = 16 kPa, Oyy =…

A:

Q: A brass rod (Young's modulus = 9.1 x 10¹0 Pa) with a length of 1.9 m and a cross-sectional area of…

A: Given:Young's modulus of brass, Eb=9.1*1010 PaLenth of brass rod, Lb=1.9 mCross-sectional area of…

Q: The figure shows the stress-strain curve for a rectangular steel test piece in tension. The test…

A:

Q: The beam is supported by two wires AB and CD that have a diameter of 12 mm and 8 mm, respectively as…

A:

Q: Using the Mohr circle or analytical solution for the plane stress case in the figure; (a) Principal…

A:

Q: The principal stresses at a point P of an elastic body are (1) = 5 N/cm², o(²) = -5 N/cm² y o(³) =…

A:

Q: The principal stresses at a point P of an elastic body are (1) = 5 N/cm², o(2) = -5 N/cm² y o(3) =…

A:

Q: as depicted in the figure. As

A: given:

Q: At a party, a parent is blowing up a birthday balloon until its diameter is n = 3.4 times the…

A: Introduction In this problem, we will compute the normal stress in the balloon after inflation, for…

Q: A body is subjected to the following stresses: og=10 MPa, oy -2 MPa, oz =3 MPa. Which of the…

A: For plane stress or 2D stress element they should two are normal stresses and one is shear stress.…

Q: a. Determine the stress matrix for this stress state if the axes are rotated 30° counterclockwise…

A: Solution: Given Data: σ=2010010100005   To Find: (a) Determine the stress matrix for the given…

Q: Question The bronze bar 3 m long with a cross-sectional area of 430 mm2 is placed between two rigid…

A:

Q: At a point on the free surface of a machine part (E = 214 GPa, G = 83 GPa), the state of the stress…

A: Given:σx=-30 MPaσy=15 MPaζxy=25 MPa

Q: Determine the normal and shear stresses that occur in the n-n plane of the figure. Present a diagram…

A: Explanation: To solve this problem, we need to use the stress transformation equations. The stepwise…

Q: The nodal coordinates and the nodal displacements for some plane stress elastic element is listed in…

A:

Q: 1. (a) If the displacement field is given by u kxy, u, = kxy, u, 2K(x + у)z where k is a constant…

A: u= ux= kxy v= uy= kxy w= uz= 2k(x+y)z Normal stress along X axis and X direction= εxx= du/dx= ky…

Q: 3) Objects 1 and 2 are positioned as shown in the figure. Object 1 is a rigid support. For object 2,…

A: Consider a body having length L,cross-sectional area A and Young's Modulus E is heated by ΔT°C.…

Q: If the cross sectional area of bar BD is 0.5 in2, what is the stress in bar BD?

A:

Q: Mohr's circle, invented by Christian Otto Mohr, is a graphical representation of the transformation…

A:

Q: The state of stress in a steel component at the critical location for the maximum load condition is…

A:

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.